ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Cumulative Damage Performance of Composite Steel Tube High-Strength Concrete Columns

Overview of the Study

This paper by Qian Jiaru, Li Ningbo, Ji Xiaodong and Cao Wanlin from Tsinghua University and Beijing University of Technology presents an experimental study on the cumulative damage performance of composite steel tube high-strength concrete columns under cyclic loading. The columns are of the "outer square, inner circle" type, meaning a square outer steel tube and a circular inner steel tube, with high-strength concrete filling the gap between them. The study involves six specimens tested under axial compression and repeated horizontal displacement loading, with the main parameters being the axial compression ratio, the square tube wall thickness and its width-to-thickness ratio, and the circular tube diameter and thickness.

Key Technical Findings

Parameter Range / Value Effect on Performance
Axial compression ratio Varied Higher ratio reduces ductility and increases damage
Square tube wall thickness Varied Thicker wall reduces cumulative damage
Square tube width-to-thickness ratio Varied Higher ratio increases local buckling risk
Circular tube diameter and thickness Varied Thicker circular tube reduces cumulative damage
Displacement angle at nominal yield 1/154 to 1/124 Good deformation capacity
Displacement angle at maximum force > 1/80 Excellent
Ultimate displacement angle > 1/60 Excellent

The failure mode is consistent: local buckling of the square tube at the base within about 300 mm, crushing of the concrete between the tubes, and bulging of the circular tube at the base. The specimens show stable hysteresis behavior, and the cumulative damage is minimal at displacement angles of 1/150 and 1/100, but becomes significant at 1/75, 1/50 and 1/33.

Engineering Implications and Practical Lessons

This paper is a good example of how composite action between two steel tubes and the concrete between them can produce excellent seismic performance. The outer square tube provides the primary flexural resistance, the inner circular tube provides confinement to the concrete, and the concrete itself provides compression resistance and energy dissipation. The key finding is that increasing the wall thickness of either the square or circular tube reduces the cumulative damage, which is a practical design recommendation.

From a fabrication standpoint, the "outer square, inner circle" configuration is challenging. The square tube is typically formed from plate by bending and welding, while the circular tube is a standard pipe. The gap between them must be filled with concrete, and the two tubes must be connected at the ends or through openings to ensure composite action. In my experience, the connection between the two tubes is critical, and it is often achieved by welding the circular tube to the square tube through openings in the square tube wall. This welding is difficult because the access is limited, and it requires a skilled welder.

One issue I have encountered is the concrete filling of the annular gap. The gap is typically 50 to 100 mm wide, and it must be filled completely without voids. This requires a high-flow concrete and careful placement. I have seen cases where the concrete did not reach the top of the column, leaving a void that reduced the composite action. The paper's test results are based on fully filled specimens, so any void will degrade the performance.

Another issue is the local buckling of the square tube at the base. The paper notes that the failure mode involves buckling of the square tube within about 300 mm of the base, which is the plastic hinge region. This is where the cumulative damage is concentrated, and it is the reason why the paper recommends increasing the wall thickness in this region. In practice, this can be achieved by using a thicker plate for the bottom segment of the square tube, or by adding stiffeners. The paper's finding that increasing the circular tube thickness also reduces cumulative damage is interesting, because it suggests that the inner tube plays a more important role than just providing confinement.

Concluding Remarks

This paper provides valuable experimental data on the cumulative damage performance of composite steel tube high-strength concrete columns, and it offers practical recommendations for improving their seismic performance. For the steel pipe industry, the implications are clear: the fabrication of such columns requires careful attention to the connection between the two tubes, the quality of the concrete filling, and the wall thickness of both tubes. The failure mode of local buckling at the base is a key concern, and it can be mitigated by increasing the wall thickness or adding stiffeners. I would recommend this paper to any engineer involved in the design of high-rise buildings with composite steel tube columns, and I would emphasize that the cumulative damage behavior is a critical design consideration that is often overlooked.