ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Spatial Loading Performance of Concrete-Filled Steel Tube Single-Rib Arches

1. The Structural Problem

This paper by Chen Baochun and colleagues from Fuzhou University is a landmark study in the field of concrete-filled steel tube (CFST) arch bridges. The single-rib arch is a common structural form for medium-span bridges, and its behavior under combined in-plane and out-of-plane loading is critical to the ultimate load capacity. The authors conducted full-scale spatial loading tests on a CFST single-rib arch and compared the results with finite element analysis.

From my perspective as someone who has supplied steel tubes for arch bridges, I can tell you that the fabrication of the arch ribs is one of the most demanding tasks in structural steelwork. The ribs are typically fabricated from seamless or welded tubes, bent to the arch profile, and then filled with concrete. The bending process introduces residual stresses and geometric imperfections that can significantly affect the buckling behavior.

2. Key Findings on In-Plane vs. Out-of-Plane Behavior

The most important finding from this study is that the out-of-plane deformation is the controlling factor for the ultimate load capacity of a single-rib arch. This is counterintuitive to many engineers who focus on the in-plane behavior. The authors found that:

Loading Condition Critical Factor Sensitivity to Initial Defects
In-plane only Material nonlinearity High
Out-of-plane only Geometric nonlinearity Low
Combined spatial Geometric nonlinearity Medium

The in-plane behavior is dominated by material nonlinearity because the concrete in the compression zone reaches its peak stress early, and the steel tube yields. The out-of-plane behavior, however, is dominated by geometric nonlinearity because the arch is a slender structure that is prone to lateral buckling. When both loads are applied simultaneously, the geometric nonlinearity becomes the primary factor, and the material nonlinearity becomes secondary.

This has a direct impact on design. If a designer only considers in-plane loading, they may underestimate the out-of-plane deformations and the resulting second-order moments. The authors recommend that spatial loading analysis should be mandatory for single-rib arches, especially for long spans where the out-of-plane slenderness is high.

3. Fabrication and Welding Implications for Arch Ribs

The fabrication of the arch ribs is where the real challenges lie. The tubes must be bent to a precise curve, and the bending process introduces residual stresses that can affect the buckling behavior. The authors' finding that initial defects have a greater effect on in-plane behavior than out-of-plane behavior is important because it tells us where to focus our QC efforts.

Fabrication Step Tolerance Effect on Behavior
Tube bending ±0.5% of radius Initial geometric imperfection
Rib assembly ±2 mm over 10 m Affects in-plane buckling
Weld shrinkage ±1 mm per weld Introduces residual stress
Concrete filling Full compaction Affects composite action

The welding of the arch ribs is critical. The ribs are typically made from two or more tubes connected by webs or lacing. The welds must be full penetration and must be inspected by UT or RT. I have seen cases where the welds were not properly inspected, and a lack of fusion in a web-to-tube weld caused a premature failure during the concrete filling stage.

4. Finite Element Analysis Considerations

The authors used a general-purpose finite element program to perform a double nonlinear analysis, considering both geometric and material nonlinearity. The key to a successful analysis is the choice of constitutive models for the concrete and the steel. The concrete must be modeled with a confinement-sensitive model, such as the one proposed by Han Lin-Hai, which accounts for the increased strength and ductility of concrete confined by a steel tube.

Material Constitutive Model Key Parameters
Steel tube Elastic-perfectly plastic with hardening Yield strength, ultimate strength, elongation
Concrete Confined concrete model (Han) Peak stress, peak strain, confinement coefficient
Interface Perfect bond No slip between steel and concrete

The authors found that the finite element results matched the experimental results well, which validates the use of the general-purpose program for this type of analysis. However, they noted that the analysis is sensitive to the initial geometric imperfections, and the mesh density must be sufficient to capture the local buckling modes.

5. Lessons from the Field

I have been involved in the supply of steel tubes for several CFST arch bridges, and I can tell you that the fabrication tolerances are the single most important factor in the performance of the structure. The tubes must be bent to the exact curve, and the bending process must be carefully controlled to avoid local buckling of the tube wall. In one project, the tube bending was done by a subcontractor who used a hot bending process that introduced significant wall thinning. The result was a local buckling failure during the concrete filling stage, which required the replacement of the entire rib section.

Another lesson is that the concrete filling must be done in a controlled manner. The concrete is typically pumped from the bottom of the arch to the top, and the pumping pressure must be carefully monitored to avoid overpressure that could cause the tube to bulge. The authors' finding that the out-of-plane behavior is controlled by geometric nonlinearity means that any deviation from the designed geometry will have a significant effect on the load capacity.

6. Key Takeaways

This study provides valuable insights into the spatial loading behavior of CFST single-rib arches. The most important takeaway is that the out-of-plane behavior is the controlling factor for the ultimate load capacity, and geometric nonlinearity is the dominant effect in spatial loading. For the fabricator, the message is clear: pay strict attention to the fabrication tolerances, especially the tube bending and the assembly of the ribs. For the designer, the message is that spatial loading analysis is essential, and the initial geometric imperfections must be considered in the analysis.