ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Lateral Impact Performance of Hollow Concrete-Filled Steel Tube Members

1. The Impact Scenario

This paper by Wang Hongxin and colleagues from Harbin Institute of Technology Shenzhen Graduate School investigates the lateral impact performance of hollow concrete-filled steel tube (CFST) members. Hollow CFST members are used in structures where weight reduction is important, such as offshore platforms, transmission towers, and protective barriers. The hollow ratio, defined as the ratio of the inner diameter to the outer diameter, is a key parameter that affects both the static and dynamic behavior.

From my experience in the offshore industry, I can tell you that impact loading is a critical design case for many structures. Ships colliding with platforms, dropped objects, and vehicle impacts are all scenarios that must be considered. The hollow CFST member is attractive because it offers a high strength-to-weight ratio, but its behavior under impact loading is not well understood.

2. Experimental and Numerical Findings

The authors conducted drop hammer impact tests on hollow CFST members with different hollow ratios and impact velocities. The key findings were:

Parameter Effect on Deformation Effect on Impact Force
Increase in impact velocity Increases deformation Increases impact force
Increase in hollow ratio Increases deformation Decreases impact force
Increase in material strength Decreases deformation Increases impact force
Increase in boundary constraint Decreases deformation Increases impact force

The experimental results showed that when the hollow ratio increases, the member becomes more compliant, and the impact force is reduced. This is because the hollow section has less material to resist the impact, and the energy is absorbed through larger deformation. The finite element analysis confirmed these trends and also showed that the material strength and boundary conditions have a significant effect on the impact performance.

The authors used a finite element model with a strain-rate-dependent material model for the steel and a confinement-sensitive model for the concrete. The strain rate effect is important because the impact loading causes high strain rates, which increase the yield strength of the steel. The authors found that the strain rate effect was significant, and the impact force was underestimated if it was not included.

3. Design and Application Considerations

The findings from this study have direct implications for the design of hollow CFST members. The hollow ratio must be carefully selected based on the expected impact loading. A higher hollow ratio reduces the weight but also reduces the impact resistance. The designer must balance these competing requirements.

Hollow Ratio Weight Reduction Impact Resistance Typical Application
0 (solid) 0% Highest Bridge piers, columns
0.3 9% High Offshore platforms
0.5 25% Moderate Transmission towers
0.7 49% Low Lightweight barriers

The boundary conditions are also critical. A member with fixed ends has a higher impact resistance than a simply supported member because the fixed ends provide additional restraint and increase the energy absorption capacity. In practice, this means that the connections at the ends of the member must be designed to resist the impact loads without failure.

4. Lessons from the Field

I have seen several cases where hollow CFST members were used in structures that were subjected to impact loading, and the results were not always satisfactory. In one offshore project, a hollow CFST member with a hollow ratio of 0.6 was used as a boat landing fender. The member was hit by a supply vessel, and the impact caused a significant dent in the member. The dent was not a structural failure, but it was severe enough to require repair.

The lesson from this incident is that the hollow ratio must be selected based on the expected impact energy. A member with a high hollow ratio may be too compliant and may deform excessively under impact, even if it does not fail. The designer must consider the acceptable deformation limit, not just the ultimate capacity.

Another lesson is that the concrete filling is critical to the impact performance. The concrete provides internal support to the steel tube, preventing local buckling and increasing the energy absorption capacity. In the hollow CFST member, the concrete is only in the annular space between the inner and outer tubes. The inner tube must be properly connected to the outer tube to ensure that the composite action is maintained.

5. Key Takeaways

This study provides valuable insights into the lateral impact performance of hollow CFST members. The most important takeaway is that the hollow ratio is the primary parameter controlling the impact resistance. A higher hollow ratio reduces the weight but also reduces the impact resistance and increases the deformation. The designer must carefully balance these competing requirements. The finite element analysis with strain-rate-dependent material models is essential for accurate prediction of the impact behavior. For the practicing engineer, the message is clear: the hollow ratio must be selected based on the expected impact loading, and the connections must be designed to resist the impact loads without failure.