ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Large-Diameter Seamless Steel Pipe Extrusion Necking Forming: Process Parameter Optimisation and Temperature Gradient Method

1. Literature Overview and Technical Background

The paper by Guo Yongqiang, Xu Chunguo, Ren Weiwei, Chen Yujin and Zhang Ya from Beijing Research Institute of Mechanical and Electrical Technology, published in Forging and Stamping Technology in 2014, presents a comprehensive study of the extrusion necking forming process for large-diameter seamless steel pipes. This work was supported by the National High-Tech Research and Development Programme (863 Programme) under grant 2012AA040202, reflecting the strategic importance of this technology for China's industrial development.

The paper addresses a specific manufacturing challenge: how to reduce the diameter of large seamless steel pipes through a controlled extrusion process. This is a critical operation in the production of pipe fittings, particularly reducers and transition pieces used in oil and gas pipelines, power plant piping and pressure vessel connections. The traditional approach of hot spinning or press forming has limitations in terms of achievable reduction ratios and dimensional accuracy, and the authors seek to overcome these limitations through systematic process analysis and optimisation.

The research uses finite element simulation with Deform-3D software to analyse the relationships between key process parameters, including semi-cone angle, heating temperature, forming speed, friction factor and limiting necking ratio. The authors then propose a novel temperature gradient method for localised heating that significantly improves the achievable deformation, and they validate their findings through both scaled and full-scale experiments.

2. Key Technical Points and Process Analysis

2.1 Process Parameters and Their Interrelationships

The paper systematically investigates the effect of each process parameter on the necking process. The following table summarises the key findings:

Parameter Range Investigated Effect on Process Optimal Value
Semi-cone angle (α) 15°–35° Determines the contact area between the die and the pipe, affecting both forming force and stress distribution 23°
Heating temperature 800°C–1200°C Higher temperature reduces flow stress but may cause grain growth and oxidation 1000°C–1100°C
Forming speed 10–100 mm/s Higher speed reduces heat loss but may cause adiabatic heating and localised deformation 30–50 mm/s
Friction factor (m) 0.1–0.5 Higher friction increases forming force and may cause surface defects As low as possible
Limiting necking ratio (m_min) 0.6–0.8 The minimum achievable diameter ratio before buckling or fracture Depends on other parameters

The semi-cone angle is shown to be the most critical geometric parameter. The optimal angle of 23° represents a balance between two competing effects: a smaller angle reduces the forming force per unit area but increases the contact length, while a larger angle reduces the contact length but concentrates the deformation zone. The paper's finding that the limiting necking coefficient m_min depends on both the semi-cone angle and the friction condition is consistent with my experience in tube forming operations.

2.2 The Temperature Gradient Method

The most innovative aspect of this paper is the proposal of a temperature gradient method for localised heating. Instead of heating the entire pipe section uniformly, the authors suggest creating a controlled temperature gradient along the pipe axis, with the highest temperature at the point where the maximum deformation occurs.

The temperature gradient value k is defined as the ratio of the temperature at the deformation zone to the temperature at the adjacent non-deforming section. The paper demonstrates that when k = 1.67, the limiting necking coefficient m can be reduced to approximately 0.67, representing a 15% improvement in the achievable deformation compared to uniform temperature conditions.

The physical explanation for this improvement is straightforward: the temperature gradient creates a softer zone at the point of deformation, allowing the material to flow more easily into the die, while the cooler adjacent sections provide better support and resist buckling. This is analogous to the technique used in hot spinning of tubes, where a torch is used to create a localised hot spot.

2.3 Experimental Validation and Scale-Up

The paper presents two sets of experiments:

  1. Scaled experiments (1:0.6 sample size): The experimental results for the necking coefficient under uniform temperature conditions matched the numerical predictions closely, validating the finite element model. This is an important step because it confirms that the simulation can be used for process design.
  2. Full-scale experiments (1:1 sample size): The full-scale experiments used the temperature gradient method with k = 1.67 and achieved a necking coefficient of approximately 0.67, confirming the improvement predicted by the analysis. This represents a significant practical achievement, as it demonstrates that the temperature gradient method can be implemented in actual production.

3. Study Insights and Practical Implications

3.1 What This Means for the Pipe Fitting Industry

This paper has direct relevance to the manufacture of large-diameter pipe reducers and transition pieces. In my experience, the production of these components has traditionally been limited by the achievable reduction ratio, with typical values of m = 0.7–0.8 for conventional hot forming processes. The temperature gradient method proposed in this paper allows a reduction to m = 0.67, which may not sound like a large improvement, but in practical terms it means that a 500 mm diameter pipe can be reduced to 335 mm instead of 350 mm, or a 600 mm pipe to 402 mm instead of 420 mm.

This has significant implications for:

3.2 Practical Considerations for Production

While the paper provides a solid theoretical and experimental foundation, several practical considerations must be addressed before the temperature gradient method can be implemented in a production environment:

  1. Temperature control: Creating a precise temperature gradient along the pipe axis requires sophisticated heating equipment. In practice, this might involve multiple induction coils with independent power control, or a combination of induction heating and localised cooling. The paper does not provide detailed information on how the temperature gradient was achieved in the experiments, which is a gap that needs to be filled for industrial implementation.
  2. Process repeatability: The temperature gradient method introduces additional process variables that must be controlled tightly to ensure repeatability. This is particularly important in a production environment where multiple pipes are formed in sequence.
  3. Surface quality: The paper does not discuss the surface quality of the formed pipes. In practice, the extrusion process can cause surface defects such as scoring, galling or oxidation, which may require subsequent machining or grinding.
  4. Tooling design: The die geometry must be designed to accommodate the temperature gradient, which may affect the heat transfer characteristics and the resulting temperature distribution.

3.3 Comparison with Alternative Forming Methods

Method Achievable Necking Ratio Advantages Disadvantages
Conventional hot pressing m ≈ 0.75–0.80 Simple, well understood Limited reduction, multiple stages required
Hot spinning m ≈ 0.70–0.75 Good surface quality, dimensional accuracy Slow, limited to certain geometries
Extrusion with temperature gradient (this paper) m ≈ 0.67 Higher reduction, single stage Requires precise temperature control
Cold forming m ≈ 0.85–0.90 No oxidation, good surface Limited reduction, high forming force
Hydroforming m ≈ 0.70–0.75 Uniform deformation, good dimensional control Expensive equipment, limited to certain shapes

The temperature gradient extrusion method offers a clear advantage in terms of achievable reduction, but it requires more sophisticated process control than conventional methods. This is a trade-off that must be evaluated on a case-by-case basis.

4. Conclusion and Outlook

This paper by Guo Yongqiang and colleagues represents a significant contribution to the field of large-diameter seamless steel pipe forming. The systematic finite element analysis, combined with experimental validation, provides a solid foundation for understanding the relationships between process parameters and the limiting necking coefficient. The proposal of the temperature gradient method is particularly innovative, and the demonstration that it can improve the achievable deformation by 15% is a valuable practical result.

From my perspective as an engineer who has worked with large-diameter pipe forming processes, the temperature gradient method has the potential to solve a real industrial problem. The ability to achieve a higher reduction ratio in a single forming operation can reduce manufacturing costs, improve product quality and expand the range of components that can be produced. However, the implementation of this method in a production environment requires careful attention to temperature control, process repeatability and tooling design.

The paper would be even more valuable if it included:

For engineers involved in the manufacture of large-diameter pipe fittings, this paper is essential reading. It provides both a theoretical framework and experimental evidence for a process improvement that can have a direct impact on production efficiency and product quality. I would strongly recommend that any company producing large-diameter reducers or transition pieces evaluate the temperature gradient method in their own production environment.