ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Pseudo-Dynamic Test of Partially Filled Circular Steel Tube Concrete Bridge Piers

Literature Overview and Context

This paper by Wang Zhanfei and colleagues from Shenyang Jianzhu University addresses a question that has become increasingly important in bridge engineering: what happens to a partially filled circular steel tube concrete bridge pier when it is subjected to severe earthquake loading? The authors conducted a substructure pseudo-dynamic test on a bridge pier that was part of a larger bridge structure, with the pier being a circular steel tube partially filled with concrete. The test simulated two earthquake levels, designated E1 and E2, using the EL CENTRO wave and the Japanese Kobe JRT-NS wave as input motions. The results were compared with numerical analysis to validate the test findings.

For those of us in the steel pipe industry, this paper is directly relevant because it concerns the structural behavior of steel tubes when they are used as bridge piers and filled with concrete. The steel tube is not just a conduit for oil or gas; it is a structural member that must withstand seismic loads, and the interaction between the steel tube and the concrete core determines the performance of the entire bridge. The paper reports that under the E1 earthquake, the pier remained in an elastic state, while under the E2 earthquake, it entered an elasto-plastic state but showed no obvious signs of damage, demonstrating good seismic performance.

Key Technical Points and Interpretation

The pseudo-dynamic test method used in this paper is a hybrid approach that combines experimental testing with numerical analysis. The substructure is tested physically, while the rest of the structure is modeled computationally, and the two are coupled in real time. This method is particularly useful for testing large structures that cannot be tested in full scale, and it allows the researcher to study the behavior of a critical component within the context of the entire structure. The authors chose a substructure approach because testing an entire bridge would be impractical, but they wanted to capture the interaction between the pier and the rest of the bridge.

The key result is that the pier remained elastic under the E1 earthquake, which is typically the design basis earthquake for a bridge, and entered the elasto-plastic range under the E2 earthquake, which is the maximum considered earthquake. The fact that the pier showed no obvious damage under E2 is a significant finding, because it suggests that the partially filled steel tube concrete pier has adequate ductility and energy dissipation capacity to survive a major earthquake without collapse.

The paper presents the displacement response and the horizontal force-displacement hysteresis curves for the pier under both earthquake inputs. These curves are the primary data for assessing the seismic performance of the pier. The hysteresis curves show that the pier dissipated energy effectively, with stable loops that indicate good ductility. The authors also compared the experimental results with numerical analysis and found good agreement, which validates the test method and the numerical model.

From a steel pipe perspective, the key technical point is the role of the concrete fill in enhancing the performance of the steel tube. The concrete core prevents local buckling of the steel tube wall, which is the primary failure mode for hollow steel tubes under compression. The concrete also increases the stiffness and strength of the pier, and it provides additional energy dissipation through cracking and crushing. However, the paper focuses on partially filled tubes, which means that the concrete does not extend the full height of the pier. This is a common design in practice, because the upper portion of the pier may need to be hollow to allow for the connection to the bridge deck or to reduce the weight of the structure.

Engineering Practice Implications

In my experience with steel pipe used in structural applications, the issue of local buckling is always a concern. When a steel tube is subjected to axial compression, the wall can buckle locally if the diameter-to-thickness ratio is too high. This is a classic problem in bridge piers, where the tube must carry significant axial loads from the bridge deck. The concrete fill solves this problem by providing internal support to the tube wall, preventing local buckling and allowing the tube to reach its full yield strength before failure.

The paper's finding that the pier showed good performance under E2 earthquake is reassuring, but I would caution that the test was conducted on a substructure, not on a full bridge. The interaction between the pier and the bridge deck, the foundation, and the adjacent spans can significantly affect the seismic response. The pseudo-dynamic method accounts for this to some extent, but it is still an approximation. In practice, I would want to see additional analysis that considers the full bridge structure, including the effects of the foundation soil and the bridge deck mass.

The paper also raises the question of how much concrete fill is optimal. The term "partially filled" suggests that the concrete does not extend the full height of the pier, but the paper does not specify the exact fill ratio. This is an important design parameter, because too little concrete may not provide sufficient local buckling resistance, while too much concrete may increase the weight and stiffness of the pier, which could attract more seismic force. In practice, the fill ratio is typically determined by the design requirements for strength, stiffness, and ductility, and it is often a compromise between these competing demands.

Standards and Quality Control Considerations

The design of steel tube concrete bridge piers is covered by several standards, including AASHTO LRFD Bridge Design Specifications in the United States, Eurocode 4 in Europe, and the Chinese code for design of concrete-filled steel tube structures. These standards provide requirements for the material properties, the geometric limits, and the design equations for strength and stability. However, they do not always provide clear guidance on the seismic performance of partially filled tubes, which is the specific topic of this paper.

From a manufacturing perspective, the quality control of the steel tube is critical. The tube must be manufactured to the specified dimensions and material properties, and the welds, if any, must be of high quality. For bridge piers, the tube is typically a large-diameter seamless or welded pipe, and the longitudinal weld, if present, must be full penetration and inspected by ultrasonic or radiographic testing. The concrete fill must also be of high quality, with proper compaction and curing, to ensure that it provides the intended support to the steel tube.

I would also note that the connection between the steel tube and the bridge deck is a critical detail. The paper does not address this in detail, but in practice, the connection must be designed to transfer the seismic forces from the deck to the pier without premature failure. This often involves a steel cap plate, anchor bolts, or a reinforced concrete transition zone, and the design of this connection is a common source of problems in bridge construction.

Key Questions and Reflections

The paper does not address the effect of the concrete fill ratio on the seismic performance. This is a significant gap, because the fill ratio is a key design parameter, and it directly affects the stiffness, strength, and ductility of the pier. I would like to see a parametric study that varies the fill ratio and evaluates the seismic performance for each case.

Another question that the paper leaves open is the effect of the steel tube wall thickness. A thicker wall provides more strength and stiffness but may also be more susceptible to local buckling if the diameter-to-thickness ratio is not properly controlled. The interaction between the wall thickness and the concrete fill is complex, and it would be valuable to study this interaction in more detail.

The paper also does not address the effect of corrosion on the steel tube. In a bridge environment, the steel tube is exposed to the elements, and corrosion can reduce the wall thickness and weaken the pier over time. This is a practical concern that should be considered in the design and maintenance of steel tube concrete bridge piers.

Study Insights and Practical Recommendations

My overall assessment is that this paper provides valuable experimental data on the seismic performance of partially filled circular steel tube concrete bridge piers. The pseudo-dynamic test method is well-suited for this type of study, and the results are consistent with what I would expect from a well-designed composite structure. The finding that the pier remained elastic under E1 and showed no obvious damage under E2 is a strong indication that this type of pier can provide adequate seismic performance.

For bridge engineers, the practical implication is that partially filled steel tube concrete piers are a viable option for bridges in seismic zones, provided that the fill ratio and wall thickness are properly designed. The steel tube provides the strength and ductility, while the concrete fill provides the local buckling resistance and additional stiffness. The combination of the two materials creates a composite structure that is both strong and resilient.

From a steel pipe manufacturing perspective, this paper highlights the importance of the steel tube quality. The tube must be manufactured to tight tolerances, with high-quality welds and consistent material properties. The pipe mill must be able to produce large-diameter tubes with the required wall thickness and strength, and the quality control must be rigorous to ensure that every tube meets the specification.

Conclusion

This paper makes a significant contribution to the understanding of the seismic performance of partially filled circular steel tube concrete bridge piers. The pseudo-dynamic test results demonstrate that this type of pier can withstand a major earthquake without significant damage, provided that the design is adequate. The combination of experimental testing and numerical analysis provides a robust validation of the performance. While the paper does not address all aspects of the problem, it provides a solid foundation for the design and construction of steel tube concrete bridge piers in seismic zones. I recommend that bridge engineers and steel pipe manufacturers study this paper and consider its findings in their own design and construction practices.