ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Bearing Capacity Analysis of Vertical Through-Plate Bolted Connections for Concrete-Filled Steel Tube Columns

Literature Overview and Core Significance

This paper from the Journal of Beijing University of Technology addresses a practical problem in the design of concrete-filled steel tube (CFST) column-to-steel beam connections for prefabricated steel structure residential buildings. The authors propose a new type of connection, the vertical through-plate bolted connection, and evaluate its bearing capacity through monotonic loading tests and finite element analysis.

The motivation for this research is clear to anyone who has been involved in the fabrication of CFST connections. The traditional inner diaphragm connection requires welding inside the steel tube, which is difficult and expensive. The outer ring plate connection uses more steel and creates protrusions that are architecturally undesirable. The proposed vertical through-plate connection addresses all three issues: it eliminates the need for internal welding, reduces steel consumption, and avoids the protruding columns.

Technical Points and Connection Behavior

Connection Geometry and Load Transfer Mechanism

The vertical through-plate connection consists of vertical plates that pass through the steel tube and are welded to the tube wall on both sides. The steel beam is then bolted to these through-plates. The load transfer mechanism involves:

  1. The beam flange forces are transferred through the bolts to the through-plates.
  2. The through-plates transfer the forces to the steel tube wall through the welds.
  3. The concrete core provides lateral support to the tube wall, preventing local buckling.
  4. The vertical plates also act as shear connectors, transferring load between the steel tube and the concrete core.

This load path is fundamentally different from the traditional inner diaphragm connection, where the beam flange forces are transferred through the diaphragm to the tube wall and then to the concrete core.

Test Results and Finite Element Analysis

The authors conducted monotonic loading tests on the connection and developed a finite element model. The key findings are:

Result Value Practical Significance
Connection classification Semi-rigid Must be considered in frame analysis
Ductility coefficient > 6 Meets seismic design requirements
Plastic rotation > 0.035 rad Adequate for seismic applications
Failure mode Ductile No brittle fracture observed
FE model correlation Good Validates the analysis approach

The semi-rigid classification is particularly important. In traditional design, connections are often classified as either pinned or rigid. The semi-rigid behavior of this connection means that the frame analysis must account for the connection stiffness, which affects the distribution of moments and shears in the frame.

The Slip Phase in Load-Deformation Behavior

The authors identified four phases in the load-deformation behavior: elastic, slip, hardening, and failure. The slip phase is a result of the bolted connection, where the bolts bear against the bolt holes after the friction resistance is overcome. This slip is a characteristic of bolted connections and must be accounted for in the design.

The slip phase has implications for the serviceability limit state. The slip can cause additional deformations under service loads, which may affect the floor vibration characteristics and the appearance of cracks in the partition walls.

Engineering Practice Considerations

Fabrication and Welding Implications

The vertical through-plate connection requires welding of the through-plates to the steel tube wall. This is a full penetration weld that must be performed from the outside, which is a significant advantage over the inner diaphragm connection. However, the welding sequence is critical to control distortion.

In my experience, the welding of through-plates to a circular or rectangular tube requires careful attention to:

  1. Weld preparation: The bevel angle and root gap must be controlled to ensure full penetration.
  2. Welding sequence: The plates should be welded symmetrically to minimize distortion.
  3. Preheating: For thick plates, preheating may be required to prevent hydrogen-induced cracking.
  4. Inspection: The welds should be inspected by ultrasonic testing or magnetic particle testing.

Bolted Connection Details

The bolted connection between the beam flange and the through-plate is a critical detail. The bolt holes must be accurately positioned, and the bolts must be properly tightened to achieve the design preload. The use of high-strength bolts is essential for the connection to behave as intended.

The slip phase in the load-deformation behavior is a concern for serviceability. The design should ensure that the slip does not occur under service loads, which means the friction resistance of the bolted connection must be sufficient for the service load level.

Prefabrication and Assembly Considerations

One of the main advantages of this connection is its suitability for prefabricated construction. The through-plates can be welded to the steel tube at the factory, and the beam can be bolted to the through-plates on site. This reduces the amount of field welding, which is a significant cost and quality advantage.

The assembly sequence on site should be carefully planned to ensure that the beams can be positioned and bolted without interference. The tolerances on the steel tube and the through-plates must be controlled to ensure that the bolt holes align properly.

Study Insights and Implications

This paper is a valuable contribution to the development of prefabricated steel structure connections. The proposed vertical through-plate connection offers several advantages over traditional connections:

  1. It eliminates the need for internal welding, which is difficult and expensive.
  2. It reduces steel consumption compared to the outer ring plate connection.
  3. It avoids the protruding columns that are architecturally undesirable.
  4. It is suitable for prefabricated construction, reducing field labor and improving quality.

The semi-rigid behavior of the connection must be considered in the frame analysis. The ductility coefficient of greater than 6 and the plastic rotation of greater than 0.035 radians indicate that the connection has adequate seismic performance.

Reference Value and Outlook

This paper provides a useful reference for engineers designing CFST column-to-beam connections for prefabricated buildings. The experimental data and finite element analysis results provide a basis for the design of this connection type.

Looking forward, the trend toward prefabricated construction will drive the development of new connection types that are easier to fabricate and assemble. The vertical through-plate connection is a good example of this trend. The key challenge will be to develop design guidelines and standard details that can be used by practicing engineers.

In my judgment, the most important takeaway is that the connection behavior is semi-rigid, not pinned or rigid. This means that the frame analysis must account for the connection stiffness, which affects the overall structural response. Engineers who assume the connection is pinned will underestimate the frame stiffness, while those who assume it is rigid will overestimate it. The actual behavior is somewhere in between, and this must be captured in the analysis.