ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Axial Compression Ultimate Bearing Capacity of Variable Cross-Section Concrete-Filled Steel Tube Lattice Columns

Why Variable Cross-Section Lattice Columns

This paper from Fujian University of Technology, Fuzhou University, and Xi'an University of Architecture and Technology addresses a specific but important problem: how to calculate the axial compression capacity of a lattice column that has a variable cross-section. Lattice columns are used in large structures such as transmission towers, bridge piers, and industrial buildings, where a single column would be too slender. A lattice column consists of two or more main chords, connected by lacing or battens, and the chords are usually concrete-filled steel tubes.

The variable cross-section is a practical feature: the column is larger at the base, where the moment is higher, and smaller at the top, where the moment is lower. This saves material and reduces the weight of the column, which is important for transportation and erection. However, it complicates the analysis, because the stiffness and the capacity vary along the length.

The authors conducted axial compression tests on variable cross-section lattice columns and found that the ultimate load decreases as the height increases and as the slope of the column limb decreases. This is intuitive: a taller column is more slender, and a column with a smaller slope is more tapered, which means the cross-section varies more along the length.

The Equivalent Length Method

The main contribution of the paper is the proposal of an equivalent length method. The idea is to replace the variable cross-section column with an equivalent constant cross-section column that has the same axial capacity. The equivalent length is calculated based on the geometry of the column, and it accounts for the variation in cross-section.

The authors propose a formula for the equivalent length, and they validate it against the test results. The formula is simple and practical, which is important for design engineers who do not have time to run a finite element analysis for every column.

The paper also provides a practical algorithm for the design of four-limb variable cross-section lattice columns. The algorithm is based on the equivalent length method, and it gives the designer a step-by-step procedure for calculating the axial capacity. This is a valuable contribution, because it brings the research into the design office.

Manufacturing and Fabrication Challenges

From a manufacturing perspective, the variable cross-section lattice column is more complex than a constant cross-section column. The main chords are tapered, which means they must be cut at an angle and welded together. The lacing or battens must be cut to fit the varying distance between the chords, and the connections must be made at the correct angles.

The tapering of the chords is the most difficult part. If the chords are made from rectangular hollow sections, the taper can be achieved by cutting the section at an angle and welding the two parts together. This is a common technique, but it requires careful fit-up and welding. I have seen tapered chords where the weld was not full penetration, and the chord failed at the weld in a test.

The lacing and battens must also be cut to fit the varying distance between the chords. This is usually done by measuring the actual distance at each location and cutting the lacing to fit. However, if the lacing is cut too short, the weld will have a gap, and if it is cut too long, the lacing will be in compression, which can cause buckling.

Design Code Implications

The paper is intended to support the development of the Chinese code for CFST structures. The current code provides formulas for constant cross-section lattice columns, but it does not provide a formula for variable cross-section columns. The equivalent length method proposed in the paper is a practical solution, and it could be incorporated into the code.

However, the method has limitations. It is based on a limited number of tests, and it may not be accurate for all geometries. The authors acknowledge this, and they recommend that the method be used with caution until more test data are available.

Closing Thoughts

This is a practical and useful paper. It addresses a real problem in the design of lattice columns, and it provides a simple method for calculating the axial capacity. The equivalent length method is easy to use, and it gives results that agree well with the test data. The practical implications are that variable cross-section lattice columns can be designed with confidence, as long as the manufacturing is done carefully. If you are designing a lattice column, this paper gives you the tool you need. If you are manufacturing one, this paper tells you what to watch for.