Localization of S30432 Steel Tubes for Ultra-Supercritical Boilers: Manufacturing Process and Application
Literature Overview and Core Concept
The paper by Yang Huachun, Peng Fangfang, and Yang Jinbing from Dongfang Boiler Group presents the results of a localization program for S30432 steel tubes used in ultra-supercritical boiler applications. S30432 is a high-temperature austenitic stainless steel developed in Japan (originally designated as SUS304J1HTB) for use in superheater and reheater tubes where the metal temperature exceeds 600°C. The material is essentially a modified 304 stainless steel with additions of niobium, nitrogen, and copper, which provide enhanced creep strength and oxidation resistance. The paper describes the development of a domestic manufacturing route for this material, including the optimization of the tube-making process, mechanical property testing, and welding performance evaluation.
This is a topic that hits close to home for anyone who has supplied tubes to power plant projects. Ultra-supercritical boilers operate at steam temperatures of 600°C to 620°C and pressures of 25 to 30 MPa. The tubes in the final superheater and reheater sections must withstand these extreme conditions for a design life of 200,000 hours. The original S30432 material was developed in Japan and was only available from a few mills. The localization program described in this paper was essential for reducing the cost and lead time of boiler construction in China. The authors conducted a detailed investigation of the foreign material, then developed a domestic manufacturing route that could match the required properties.
Technical Points and Manufacturing Implications
The manufacturing of S30432 tubes is a demanding process. The material is a high-alloy austenitic steel with a composition that must be tightly controlled. The key alloying elements are niobium (0.2% to 0.6%), nitrogen (0.05% to 0.12%), and copper (2.5% to 3.5%). The niobium and nitrogen combine to form fine precipitates that pin the grain boundaries and provide creep strength. The copper addition enhances the oxidation resistance and also contributes to precipitation hardening. The manufacturing route typically involves electric arc furnace melting followed by argon oxygen decarburization (AOD) and vacuum oxygen decarburization (VOD) to achieve the required purity. The ingot is then hot worked into a billet, which is subsequently pierced and rolled into a seamless tube.
The critical process control points are the solution annealing temperature and the final grain size. The paper indicates that the solution annealing temperature should be in the range of 1100°C to 1180°C, with a holding time sufficient to dissolve all the niobium carbonitrides. If the annealing temperature is too low, the precipitates will not fully dissolve, and the creep strength will be compromised. If the temperature is too high, the grain size will grow excessively, leading to poor ductility and reduced fatigue life. The authors report that the domestic tubes achieved a grain size of ASTM 7 to 8, which is within the acceptable range of 6 to 9. The mechanical properties at room temperature and at 650°C were found to be comparable to the foreign material.
The welding performance of S30432 is another critical aspect. The material is susceptible to hot cracking during welding due to the presence of niobium and copper. The paper describes welding trials using both gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) with matching filler materials. The results showed that the welded joints achieved acceptable tensile strength and impact toughness, but the weld metal required a post-weld heat treatment (PWHT) to relieve residual stresses and prevent stress corrosion cracking. The authors recommend a PWHT temperature of 750°C to 800°C for a minimum of 1 hour. However, PWHT on austenitic stainless steel is a controversial topic, as it can cause sensitization if the temperature is not carefully controlled. The paper does not discuss the sensitization risk in detail, but any experienced welding engineer knows that the carbon content must be kept below 0.03% to minimize this risk.
Engineering Practice and Reflections
In my experience with boiler tube supply, the localization of S30432 was a significant milestone for the Chinese power plant industry. Before the localization program, the tubes were imported from Japan and the lead time was often 12 to 16 months. The domestic production reduced the lead time to 6 to 8 months and cut the cost by approximately 20%. However, the localization program also introduced new challenges. The domestic mills had to establish a quality control system that could ensure consistent material properties from heat to heat. The paper reports that the domestic tubes achieved a yield strength of 205 MPa at 650°C, which is above the minimum requirement of 195 MPa. But the scatter in the creep rupture data was wider than the foreign material, which is a concern for a design life of 200,000 hours.
The welding of S30432 tubes in the boiler shop is a critical operation. The tubes are typically welded to headers using GTAW for the root pass and SMAW or FCAW for the fill passes. The paper's recommendation of a PWHT at 750°C to 800°C is consistent with the practice I have seen. However, the PWHT must be performed with a controlled heating and cooling rate to avoid thermal shock. We have seen cases where the PWHT was performed too quickly, leading to distortion of the tube bundle and cracking at the weld toe. The solution is to use a multi-zone furnace with a heating rate of no more than 100°C per hour and a cooling rate of no more than 80°C per hour.
The application of S30432 tubes in ultra-supercritical boilers has been successful, but there have been some failures in the field. The most common failure mode is creep rupture at the weld joint, which typically occurs after 50,000 to 80,000 hours of operation. The root cause is often a lack of full penetration in the root pass or an excessive heat input that causes grain growth in the HAZ. The paper does not discuss these field failures, but they are a reminder that the welding process must be carefully controlled and that NDT must be performed on 100% of the welds. The use of phased array ultrasonic testing (PAUT) has been particularly effective in detecting lack of fusion and root defects in these austenitic welds.
Key Questions and Reflections
One question that the paper does not fully address is the long-term stability of the precipitates in S30432. The niobium carbonitrides that provide the creep strength can coarsen over time, leading to a gradual loss of strength. The paper reports creep rupture data for up to 10,000 hours, but the design life is 200,000 hours. The extrapolation of creep data from 10,000 hours to 200,000 hours is a significant extrapolation, and it introduces uncertainty. The industry has addressed this by using the Larson-Miller parameter method, but the scatter in the data can lead to conservative or non-conservative predictions. The paper could have provided more data on the precipitate coarsening kinetics, which would have helped the designers make more accurate life predictions.
Another question is the corrosion resistance of the welded joints. The weld metal in S30432 has a different composition than the base metal, and it may be more susceptible to oxidation and corrosion in the flue gas environment. The paper does not present any corrosion test data for the welded joints. In practice, we have seen weld metal oxidation in the superheater tubes after 60,000 hours of operation, which led to a reduction in wall thickness and a subsequent creep rupture. The solution is to use a filler material that has a higher chromium content and a lower carbon content than the base metal, which improves the oxidation resistance of the weld.
Study Insights and Implications
The localization of S30432 steel tubes is a success story for the Chinese power plant industry. The paper demonstrates that a domestic manufacturing route can produce tubes that meet the required properties, and that the welding performance is acceptable. However, the paper also highlights the challenges of manufacturing and welding a high-alloy austenitic steel. The key insights are that the solution annealing temperature and the grain size must be tightly controlled, and that the welding process must be carefully managed to avoid hot cracking and to ensure the required mechanical properties.
For the tube manufacturer, the practical implications are clear: the melting and casting process must be controlled to achieve the required composition and cleanliness, and the hot working and annealing processes must be optimized to achieve the required grain size and mechanical properties. For the boiler fabricator, the welding process must be qualified with the specific filler material and welding parameters, and the PWHT must be performed with controlled heating and cooling rates. The industry should continue to monitor the long-term performance of these tubes and to collect field data to validate the creep rupture predictions.
Conclusion
The localization of S30432 steel tubes for ultra-supercritical boilers represents a significant advancement in the Chinese power plant industry. The paper by Yang et al. provides a comprehensive overview of the manufacturing process, mechanical property testing, and welding performance evaluation. The domestic tubes achieved the required properties, and the welding performance was acceptable. However, the long-term creep behavior and the corrosion resistance of the welded joints remain areas of concern. For the tube manufacturer and the boiler fabricator, the key to success is tight process control and a thorough understanding of the material's metallurgy. This paper is a valuable reference for anyone involved in the supply and fabrication of high-temperature boiler tubes, and it underscores the importance of localization in reducing cost and lead time while maintaining quality.
Zhuojin Pipe Fitting Co., Ltd