ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Failure Analysis of Dissimilar Steel Tube Joints in Boiler Superheaters: A Practical Review

Background and Core Findings

This paper addresses a problem that has caused countless boiler outages and, in some cases, catastrophic failures: the premature failure of dissimilar steel tube joints in boiler superheaters. The authors analyse a joint that failed after approximately 40,000 hours of high-temperature service, with a crack propagating along the heat-affected zone (HAZ) of the heat-resistant steel. The joint was repaired by manual arc welding, but the crack reappeared after a short period of service. The failure analysis reveals that the initial failure was due to creep, caused by pearlite spheroidisation, carbide aggregation, and carbon migration in the HAZ. The subsequent failure was due to stress corrosion cracking (SCC), caused by the combined action of residual stress and a chloride-containing steam environment.

The practical significance of this work is that it identifies the root causes of a common failure mode and provides a solution: using nickel-based filler wire with TIG welding for the transition joint. This solution is now widely adopted in the industry, but this paper provides the metallurgical evidence to support it.

Key Technical Points and Failure Mechanisms

Failure Stage Mechanism Root Cause Key Evidence
Initial failure Creep Carbon migration in HAZ, pearlite spheroidisation Microstructure analysis, carbide aggregation
Repair Manual arc welding Inadequate filler material, residual stress Crack reappearance after repair
Subsequent failure Stress corrosion cracking Residual stress + chloride-containing steam Fracture surface analysis, chloride detection

The creep failure mechanism is the most critical finding. In a dissimilar steel joint, the carbon migrates from the lower-alloy steel to the higher-alloy steel during high-temperature service. This creates a carbon-depleted zone in the HAZ of the lower-alloy steel, which reduces its creep strength. The pearlite spheroidisation further reduces the strength, and the carbide aggregation creates stress concentrations that promote crack initiation.

The stress corrosion cracking mechanism is equally important. After the repair, the residual stress from the welding is combined with the chloride-containing steam environment, which is a classic SCC scenario. The chloride ions attack the passive oxide film on the steel surface, and the tensile stress opens the crack. The crack propagates along the grain boundaries, leading to rapid failure.

Interpretation of the Welding Metallurgy

The welding of dissimilar steel joints is one of the most challenging tasks in the power industry. The two steels have different thermal expansion coefficients, different creep strengths, and different metallurgical characteristics. The welding process must be carefully controlled to minimise the carbon migration and to ensure that the joint has adequate creep strength.

The use of nickel-based filler wire is the key solution. Nickel-based alloys have a thermal expansion coefficient that is intermediate between the two steels, which reduces the thermal stress. They also have a high creep strength and are resistant to carbon migration. The TIG welding process provides a clean, high-quality weld with good penetration and minimal heat input, which reduces the HAZ width and the carbon migration.

From a fabrication perspective, the welding of dissimilar steel joints requires careful preparation and control. The joint geometry must be designed to provide adequate access for the welder, and the preheat and interpass temperatures must be controlled to prevent cracking. The welding must be performed by qualified welders, and the weld must be inspected by NDT methods to ensure that it is free from defects.

Integration with Engineering Practice

The failure analysis in this paper has direct implications for the fabrication and repair of dissimilar steel joints in boilers. In my experience, the most common cause of premature failure in these joints is the use of the wrong filler material. Many fabricators use a standard filler material that is not compatible with the two steels, leading to carbon migration and premature failure.

The paper also highlights the importance of post-weld heat treatment (PWHT). After welding, the joint must be heat-treated to relieve the residual stress and to temper the HAZ. However, PWHT of dissimilar steel joints is challenging, as the two steels require different heat treatment temperatures. The nickel-based filler material allows a single PWHT temperature that is suitable for both steels.

I have seen boiler superheaters fail because the PWHT was not performed correctly. The residual stress from the welding, combined with the chloride-containing steam environment, caused SCC within a few months of service. The failure was catastrophic, and the boiler was out of service for several weeks.

Key Questions and Reflections

The paper raises a question that is central to the design and fabrication of dissimilar steel joints: what is the appropriate filler material for a given combination of steels? The answer depends on the service temperature, the steam environment, and the mechanical properties of the two steels. The nickel-based filler material is a good general solution, but it may not be optimal for all cases.

I would also question whether the repair procedure described in the paper was appropriate. The manual arc welding repair was performed without adequate preheat and PWHT, which led to the recurrence of the crack. A more appropriate repair would have been to remove the entire joint and replace it with a new joint, using the nickel-based filler material and TIG welding.

Study Insights and Implications

The most valuable insight from this paper is the identification of the root causes of the failure and the development of a solution. The use of nickel-based filler material with TIG welding is now standard practice in the industry, and this paper provides the metallurgical evidence to support it.

From a delivery perspective, the paper reminds me that the fabrication of dissimilar steel joints requires careful control of the welding process and the filler material. The failure analysis provides a clear lesson: if you use the wrong filler material, the joint will fail prematurely, and the consequences can be catastrophic.

Conclusion and Reference Value

This paper provides a comprehensive failure analysis of a dissimilar steel tube joint in a boiler superheater, and it identifies the root causes of the failure: creep due to carbon migration and stress corrosion cracking due to residual stress and chloride-containing steam. The paper also provides a solution: using nickel-based filler wire with TIG welding for the transition joint. For the industry, the paper is a reminder that the fabrication of dissimilar steel joints requires careful control of the welding process and the filler material, and that the consequences of getting it wrong can be catastrophic. I would recommend this paper to any engineer involved in the fabrication or repair of dissimilar steel joints in boilers, with the caveat that the solution must be implemented with proper preheat and PWHT to be effective.