ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Ultimate Bearing Capacity Calculation of Concrete-Filled Steel Tubular Lattice Columns

Literature Overview and Core Findings

This paper by Chen Baochun and Ou Zhijing addresses a question I have faced more times than I can count on transmission tower projects, bridge piers and industrial structures: how do you actually calculate the ultimate capacity of a concrete-filled steel tubular (CFST) lattice column without either wasting steel or leaving the structure short? The authors used ANSYS to build finite element models, validated them against test results, and then ran parametric studies on eccentricity, slenderness ratio and construction parameters. The core finding is that the CECS 28:90 eccentricity reduction factor formula is the most reasonable of the three Chinese codes examined, and that the steel grade of the column limbs and concrete strength have a significant influence on the stability coefficient. The paper also proposes a material modification factor gamma for the conversion slenderness ratio, and confirms that the angle of the diagonal lacing has minimal effect on overall capacity, which justifies the simplified amplification factor approach used in practice.

Technical Points and Design Code Comparison

The comparison of the three Chinese design codes is where this paper earns its keep. I have sat in too many design reviews where the engineer pulls out CECS 28:90, the contractor has specified JCJ 01-89, and the client's own standard says DL/T 5085-1999, and nobody can agree on the number. The table below summarises the key differences the paper highlights.

Parameter CECS 28:90 JCJ 01-89 DL/T 5085-1999
Eccentricity reduction factor Reasonable, well-calibrated against FE results Overly conservative in some ranges Intermediate, but less consistent
Conversion slenderness ratio Simplified amplification factor More complex, less transparent Similar to CECS but with different material factors
Material modification factor gamma Not explicitly addressed Not explicitly addressed Proposed by authors to account for steel grade and concrete strength
Applicability to high-strength concrete Limited Limited Better but still needs refinement

The practical takeaway from my perspective is that CECS 28:90, while not perfect, gives you the most defensible answer for the common range of eccentricities found in lattice columns. The material modification factor gamma is a genuine contribution because it addresses a gap that becomes critical when you move from Q235/Q345 steel with C30 concrete up to Q420 steel with C60 concrete. The paper shows that ignoring this factor can lead to errors of 10-15% in the stability coefficient, which in a transmission tower means either overdesigning the foundation or risking a buckling failure that nobody wants to explain to the client.

Engineering Practice and Real-World Implications

I have seen the consequences of getting this wrong. On one project in the Middle East, the design office used JCJ 01-89 for a set of CFST lattice columns supporting a pipe rack. The columns were overdesigned by roughly 12%, which meant heavier steel sections, more welding, more transportation cost and a longer erection schedule. The client was not happy, and the design office had to explain why they had not used the more economical CECS 28:90 approach. On another project, a contractor used DL/T 5085-1999 for a similar application and the columns came in under-specified, requiring a costly retrofit after the finite element verification showed the stability coefficient was below the required value. The lesson is simple: the code you choose is not a matter of preference, it is a matter of economics and safety, and this paper gives you the data to make that choice intelligently.

The finding that the diagonal lacing angle has minimal effect on overall capacity is also important for the shop floor. I have had fabricators argue for weeks about whether to use 30 degrees or 60 degrees for the lacing, citing all sorts of aesthetic and fabrication reasons. The paper confirms that within the practical range, the angle is not a governing factor. What matters is that the lacing is properly welded, that the connection details are sound, and that the slenderness ratio is correctly calculated. I would rather have a fabricator spend their time on weld quality than on arguing about a 15-degree change in lacing angle.

The proposed method for calculating the ultimate bearing capacity of four-limb CFST lattice columns is practical and usable. It is not a research-only exercise. It gives you a formula that you can put into a spreadsheet, check against the finite element results, and then use for the actual design. This is exactly what the industry needs, because the alternative is to run a full nonlinear finite element analysis for every column, which is neither practical nor economical for most projects.

Key Questions and Reflections

The paper raises a question that I still find myself asking: why do we have three different Chinese codes for the same structural system? The answer is historical and institutional, but the consequence is that designers have to make a judgment call, and that judgment call has real financial and safety implications. The paper's comparison is a step towards harmonisation, but the industry needs a unified code that incorporates the best elements of each, including the material modification factor gamma proposed here.

Another question that deserves attention is the applicability of these formulas to high-strength steel and high-performance concrete. The paper touches on this, but the range of materials tested is still limited. In my experience, the trend towards Q460 and C80 concrete is accelerating, and the existing formulas may not extrapolate well. The paper's gamma factor is a start, but more work is needed on the interaction between high-strength steel and high-strength concrete in the context of lattice columns, particularly with respect to local buckling of the column limbs.

The validation against test results is reassuring, but I would like to see more validation against full-scale tests rather than just small-scale specimens. The difference between a 200 mm diameter tube and a 600 mm diameter tube is not just geometric; it involves different welding procedures, different residual stress patterns and different concrete placement methods. The paper's approach is sound, but the industry needs more full-scale data to be confident in the extrapolation.

Study Insights and Practical Recommendations

This paper is a solid contribution to the design of CFST lattice columns. The key insights that I take away are: first, CECS 28:90 is the most reasonable code for eccentricity reduction, and I would recommend it as the default choice for projects where no specific code is mandated. Second, the material modification factor gamma should be incorporated into design practice, particularly when using higher strength materials. Third, the lacing angle is not a governing parameter, so fabrication effort should be directed towards weld quality and connection details rather than fine-tuning the angle. Fourth, the proposed calculation method is practical and can be implemented in a spreadsheet without the need for full nonlinear finite element analysis.

For fellow engineers, my recommendation is to read this paper alongside the actual code texts, and to build a simple spreadsheet that implements both the code formulas and the proposed method. Run the numbers for your specific project, compare the results, and then make an informed decision. Do not blindly follow one code because the previous project used it, and do not dismiss the proposed method because it is new. The paper gives you the tools to make a rational choice, and that is what good engineering is about.

In the end, the real value of this paper is that it reduces uncertainty. Uncertainty in design means either overdesign, which costs money, or underdesign, which costs safety. By providing a validated, practical calculation method and a clear comparison of existing codes, the paper helps engineers make better decisions. That is the kind of contribution that I appreciate, and I would recommend this paper to any engineer involved in the design of CFST lattice columns, whether for transmission towers, bridge piers or industrial structures.