ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Axial Compression Capacity of High-Strength Steel Tubes for Transmission Towers

Background and Code Gap

High-strength steel tubes are increasingly used in ultra-high voltage (UHV) transmission towers, where the loads are large and the members are long and slender. The steel grades used are typically Q460, Q500 or Q550, with yield strengths of 460 to 550 MPa, compared to the conventional Q235 or Q345 grades. The problem is that the Chinese design codes for transmission towers (e.g., DL/T 5154) were developed primarily for conventional steel grades, and the design parameters for high-strength steel are not fully covered. The 2010 paper by Yang Longyu, Li Zhengliang, Wei Lei, Kang Dongchang, Ma Zhenyi and Duan Bei from Chongqing University addresses this gap by comparing existing design methods, performing finite element analysis, and conducting tests on high-strength steel tubes. The study concludes that the existing code methods can be used for high-strength steel tubes, and that the optimal slenderness ratio for transmission tower applications is in the range of 40 to 80. For the steel pipe industry, this paper has direct implications for the design, manufacturing and quality control of high-strength steel tube members for transmission towers.

Research Approach

The research combined three approaches: a comparison of existing design methods, finite element analysis, and experimental testing. The existing design methods include the Chinese code method (based on the Perry-Robertson formula), the European method (EC3), and the American method (AISC). The finite element analysis used shell or solid elements to model the tube, with geometric and material non-linearity, and considered both global buckling and local buckling. The experimental tests were conducted on high-strength steel tubes with various slenderness ratios, loaded in axial compression to failure.

Approach Purpose Key Output
Code comparison Evaluate whether existing methods are conservative for high-strength steel Stability factor curves for various slenderness ratios
Finite element analysis Model the actual buckling behaviour, including local and global interaction Load-displacement curves, failure modes
Experimental tests Validate the FEM and code predictions Actual ultimate loads, failure modes

The comparison showed that the existing Chinese code method, when applied to high-strength steel tubes, gives results that are consistent with the FEM and the test results, provided the appropriate material properties are used. The European and American methods also give reasonable results, but with some differences in the transition region between the plastic and elastic buckling ranges. The key conclusion is that the Chinese code method can be used for high-strength steel tubes without major modification, which is a practical and important finding for designers.

Findings and Design Implications

The most important finding is the optimal slenderness ratio range of 40 to 80. This is the range where the high-strength steel tube achieves the best balance between material efficiency and buckling resistance. Below 40, the tube is stocky and the failure is by material yielding rather than buckling — the high strength of the steel is fully utilized, but the member is heavy. Above 80, the tube is slender and the failure is by elastic buckling — the high strength of the steel is not fully utilized because the buckling stress is much lower than the yield strength. The range of 40 to 80 is therefore the "sweet spot" for transmission tower applications.

Slenderness Ratio Range Failure Mode Material Utilization Recommendation
< 40 Material yielding High (stress reaches yield) Acceptable but heavy; consider smaller tube
40–80 Inelastic buckling Optimal (stress close to yield) Recommended for transmission towers
> 80 Elastic buckling Low (stress well below yield) Inefficient; consider larger tube or bracing

The practical implication is that the designer should select the tube diameter and wall thickness so that the slenderness ratio falls within the 40 to 80 range. This is a design guideline that is easy to apply and that ensures the high-strength steel is used efficiently. The paper also notes that the local buckling of the tube wall must be checked — the D/t ratio must be within the limits specified in the code to prevent local buckling before global buckling. For high-strength steel, the D/t limit is more restrictive than for conventional steel because the higher yield strength increases the susceptibility to local buckling.

Practical Considerations for Tube Supply

For the steel pipe manufacturer, this paper highlights several important considerations. First, the material properties of the high-strength steel tube must be verified — the yield strength, tensile strength and elongation must meet the specified grade, and the test certificates must be provided with each delivery. Second, the dimensional tolerances are critical — the outer diameter and wall thickness must be within the specified tolerances, because a deviation in wall thickness affects both the cross-sectional area and the moment of inertia, which directly affects the buckling capacity. Third, the residual stresses from the manufacturing process (cold-forming, welding) must be considered. Cold-formed tubes have residual stresses that reduce the buckling capacity, and the reduction factor depends on the D/t ratio and the forming process. The paper does not address this directly, but it is a well-known effect in the industry, and it should be accounted for in the design.

The manufacturing route for high-strength steel tubes for transmission towers is typically either cold-formed from strip (ERW or HFW welded) or hot-rolled seamless. The cold-formed route is more economical for large quantities, but the residual stresses are higher. The hot-rolled seamless route has lower residual stresses but is more expensive. For transmission towers, the cold-formed route is usually preferred because of the cost, and the design must account for the residual stresses. The paper's conclusion that the existing code method can be used for high-strength steel tubes is reassuring, but the designer must ensure that the residual stress effects are included in the calculation, either through the code's stability factor or through a separate reduction factor.

Concluding Remarks

The paper provides a practical and valuable contribution to the design of high-strength steel tubes for transmission towers. The finding that the existing Chinese code method can be used for high-strength steel tubes simplifies the design process and avoids the need for a separate design code. The optimal slenderness ratio range of 40 to 80 is a clear and useful guideline that helps designers select the most efficient tube geometry. For the steel pipe industry, the paper reinforces the importance of material verification, dimensional control and residual stress management. The next step in this research should be to investigate the effect of residual stresses on the buckling capacity of cold-formed high-strength steel tubes, and to develop a reduction factor that can be applied in design. Until then, the designer should use a conservative approach and verify the buckling capacity with full-scale tests if the application is critical.