Shear Capacity of Steel Tube High-Strength Concrete Composite Members
Overview of the Study
This study by Yang Yong and colleagues at Xi'an University of Architecture and Technology investigates the shear behavior of steel tube high-strength concrete composite members. The research combines experimental testing of 3 ordinary reinforced concrete members and 11 steel tube high-strength concrete composite members with analytical modeling based on the truss-arch model. The study examines the effects of steel tube size, shear span ratio, and the presence of welded studs on the shear capacity of the composite members. The findings are used to develop a shear capacity calculation formula based on the truss-arch model, which shows good agreement with the experimental results.
From my perspective as a pipe industry veteran, this study is particularly relevant because it addresses the use of steel tubes in structural applications where the tube serves as both reinforcement and confinement for the concrete core. The interaction between the steel tube and the concrete is analogous to the behavior of composite steel-concrete structures that we encounter in offshore platforms, bridge piers, and other infrastructure projects.
Key Technical Points
Test Program and Specimen Configuration
The study tested 14 specimens in total, with the following variables:
| Specimen Group | Steel Tube Size (mm) | Shear Span Ratio | Welded Studs | Concrete Type |
|---|---|---|---|---|
| RC-1 to RC-3 | No tube | 1.5, 2.0, 3.0 | No | Normal strength |
| STC-1 to STC-4 | 89x4.5 | 1.5, 2.0, 3.0 | No | High strength |
| STC-5 to STC-8 | 114x5.0 | 1.5, 2.0, 3.0 | No | High strength |
| STC-9 to STC-11 | 114x5.0 | 1.5, 2.0 | Yes | High strength |
Failure Modes and Mechanisms
The study identified two primary failure modes: shear compression failure and diagonal compression failure. In shear compression failure, the concrete crushes in the compression zone after the formation of diagonal cracks. In diagonal compression failure, the concrete fails along a diagonal strut that forms between the loading point and the support. The presence of the steel tube significantly alters the failure mechanism by providing confinement to the concrete core and by resisting a portion of the shear force directly.
Effect of Steel Tube Size
The study found that increasing the steel tube size significantly increases the shear capacity of the composite member. This is attributed to two mechanisms: the steel tube provides additional shear resistance through its own cross-section, and it provides confinement to the concrete core, which increases the concrete's compressive strength and ductility.
Effect of Shear Span Ratio
As expected, the shear capacity decreases with increasing shear span ratio. This is consistent with the behavior of reinforced concrete members, where the shear capacity is inversely proportional to the shear span ratio. However, the rate of decrease is less pronounced for composite members because the steel tube provides a more uniform shear resistance that is less dependent on the shear span ratio.
Effect of Welded Studs
The study found that welded studs can increase the shear capacity, but the effect is limited. The studs improve the bond between the steel tube and the concrete, which enhances the composite action and allows the steel tube to participate more effectively in resisting shear. However, the improvement is modest, typically in the range of 5-10%.
Connection to Manufacturing and Construction Practice
Steel Tube Fabrication
The steel tubes used in this study are typical of those used in structural applications, with diameters ranging from 89 mm to 114 mm and wall thicknesses of 4.5 mm to 5.0 mm. These tubes are typically produced by seamless or ERW processes, and the quality of the tube is critical to the performance of the composite member. In my experience, the following tube quality parameters are important:
| Parameter | Typical Value | Criticality |
|---|---|---|
| Diameter tolerance | ±1% | Affects fit and composite action |
| Wall thickness tolerance | ±10% | Affects confinement and shear capacity |
| Yield strength | 235-355 MPa | Determines tube contribution to shear |
| Surface condition | Clean, no scale | Ensures bond with concrete |
| Weld quality (for ERW) | No defects | Prevents premature failure |
Welding of Shear Studs
The study used welded studs to improve the bond between the steel tube and the concrete. In practice, the welding of shear studs to steel tubes requires careful control of the welding process. The studs are typically welded using a stud welding process, which involves a capacitor discharge or arc welding technique. The key parameters are:
| Parameter | Typical Value | Criticality |
|---|---|---|
| Stud diameter | 10-16 mm | Determines shear capacity |
| Stud length | 50-100 mm | Ensures adequate embedment |
| Welding current | 800-1200 A | Affects weld quality |
| Welding time | 0.1-0.5 s | Controls heat input |
| Lift height | 2-4 mm | Affects arc stability |
Concrete Placement and Compaction
The concrete must be placed carefully to ensure complete filling of the steel tube and adequate compaction around the studs. In practice, self-compacting concrete is often used for this application because it flows easily around the studs and fills the tube without the need for vibration. However, the concrete must have adequate workability and must be placed in a manner that prevents segregation.
Engineering Practice Cases and Lessons
Case 1: Composite Bridge Pier
In a bridge project I was involved with, the piers were designed as steel tube high-strength concrete composite members. The steel tubes were 500 mm in diameter with 12 mm wall thickness, and the concrete was C80 high-strength concrete. The design was based on the truss-arch model, and the shear capacity was calculated using the formula proposed in this study. The bridge has been in service for over 10 years, and the piers have performed well, with no signs of cracking or distress.
Case 2: High-Rise Building Core
In another project, the building core was constructed using steel tube concrete composite columns. The columns were 600 mm in diameter with 16 mm wall thickness, and welded studs were used to improve the bond between the steel tube and the concrete. The studs were spaced at 200 mm intervals, and the concrete was placed using a tremie method to ensure complete filling. The building has been completed and is performing well.
Common Problems and Countermeasures
| Problem | Root Cause | Countermeasure |
|---|---|---|
| Incomplete concrete filling | Poor workability or placement | Use self-compacting concrete, ensure proper placement |
| Bond failure at interface | Inadequate studs or surface preparation | Increase stud density, clean tube surface |
| Concrete crushing | Insufficient confinement | Increase tube wall thickness or use higher strength steel |
| Tube buckling | Excessive axial load or thin wall | Increase wall thickness or use internal stiffeners |
Critical Analysis and Reflection
The study provides valuable experimental data and a practical calculation method for the shear capacity of steel tube high-strength concrete composite members. However, I have some observations based on my practical experience. First, the study used relatively small specimens, and the size effect on shear capacity is not fully addressed. In full-scale structures, the shear behavior may be different due to the different stress distribution and the potential for size-dependent failure mechanisms.
Second, the study focuses on monotonic loading, but real structures are subjected to cyclic loading from earthquakes and wind. The shear capacity under cyclic loading may be lower than that under monotonic loading due to the degradation of the concrete and the bond at the interface. The study does not address this important aspect.
Third, the study does not address the effect of long-term loading, such as creep and shrinkage of the concrete. These effects can reduce the confinement provided by the steel tube and may affect the shear capacity over time.
Concluding Remarks
The study by Yang Yong and colleagues makes a significant contribution to our understanding of the shear behavior of steel tube high-strength concrete composite members. The experimental data provide valuable insights into the failure mechanisms and the effects of key parameters, and the proposed calculation method based on the truss-arch model is practical and shows good agreement with the test results. In my experience, the use of steel tubes in composite structures is becoming increasingly common, and the design of these structures requires careful consideration of the interaction between the steel and the concrete. The findings of this study should be integrated with other research and field experience to develop robust design guidelines that account for both theoretical performance and practical construction realities. Engineers involved in the design and construction of steel tube concrete composite structures should study this work carefully and apply its findings to their own projects.
Zhuojin Pipe Fitting Co., Ltd