ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Impact Compression Characteristics and Ultimate Strength Determination Method for Steel Tube RPC

Literature Overview

This paper by Chen Wanxiang, Guo Zhikun, Jiang Meng, Yan Fengguo and Liang Wenguang, published in Journal of Vibration and Shock (2016, Vol. 35, No. 20, pp. 160-166), presents an experimental study of the impact compression behaviour of steel tube reactive powder concrete (RPC). The work was conducted at the State Key Laboratory of Explosion and Impact Disaster Prevention and Mitigation at the PLA University of Science and Technology, with support from the National Natural Science Foundation of China.

RPC is a high-performance cementitious material with compressive strength typically exceeding 150 MPa. When confined in a steel tube, the composite material exhibits enhanced strength, ductility and energy absorption capacity. The paper uses a Φ74 mm split Hopkinson pressure bar (SHPB) to test 20 steel tube RPC specimens and 20 plain RPC specimens at different loading rates, obtaining dynamic stress-strain curves, peak stresses and peak strains.

Core Findings and Technical Points

The paper reports several key findings from the SHPB tests:

Parameter RPC Steel Tube RPC
Peak stress Increases with strain rate Increases with strain rate, higher than RPC
Peak strain Increases with strain rate Increases with strain rate, higher than RPC
Ductility Moderate Significantly improved
Failure mode Brittle fragmentation Confined, retains integrity

The paper concludes that steel tube RPC has higher strength, better ductility and better integrity than plain RPC under impact loading. The steel tube provides confinement, which prevents the RPC from spalling and keeps the specimen intact even at high strain rates.

The paper also investigates the effect of steel tube wall thickness on the dynamic behaviour. At a given impact velocity, a thinner steel tube shows a more pronounced yield plateau and strain hardening, and the peak strain is significantly increased. This suggests that the wall thickness affects the confinement level and the energy absorption capacity.

Wall Thickness Effect on Dynamic Behaviour
Thin Pronounced yield plateau, significant strain hardening, larger peak strain
Thick Higher peak stress, less pronounced yield plateau, smaller peak strain

The paper also proposes a method for determining the ultimate strength of steel tube RPC under impact loading. The method is based on the static axial ultimate bearing capacity formula for CFST members, with a strain rate effect factor introduced to account for the dynamic loading condition. The theoretical results show some relative error compared to the test results, but the error decreases as the response strain rate increases.

Integration with Engineering Practice

This paper is relevant to the design of protective structures, such as blast-resistant walls, impact-resistant columns and protective barriers. Steel tube RPC is a promising material for these applications because it combines the high strength of RPC with the ductility and energy absorption capacity of the steel tube.

I have seen steel tube concrete used in protective structures, and the performance under impact loading is a critical design parameter. The paper provides valuable data on the dynamic behaviour of steel tube RPC, which can be used to validate design models and to develop design guidelines.

The finding that the steel tube wall thickness affects the dynamic behaviour is important for design. A thinner tube provides more ductility and energy absorption, while a thicker tube provides higher strength. The designer must balance these two requirements based on the specific application.

The proposed method for determining the ultimate strength is a practical tool, but the relative error should be understood. The paper reports that the error decreases as the response strain rate increases, which suggests that the method is more accurate for high strain rate loading. For low strain rate loading, the method may overestimate or underestimate the ultimate strength.

Key Questions and Reflections

One question that the paper does not fully address is the effect of the steel tube-RPC interface on the dynamic behaviour. The bond between the steel tube and the RPC is critical for load transfer, and the bond strength may be affected by the strain rate. If the bond degrades under impact loading, the composite behaviour may be different from what the tests show.

Another issue is the scale effect. The tests were conducted on Φ74 mm specimens, which are relatively small. The behaviour of full-scale members may be different, particularly with respect to the confinement effect and the failure mode. The paper does not provide guidance on how to extrapolate the results to full-scale members.

The paper also does not address the long-term durability of steel tube RPC. RPC is a dense material with low porosity, but it can still be affected by environmental conditions. The steel tube provides protection, but the interface between the steel and the RPC may be susceptible to corrosion if water penetrates.

Study Insights and Implications

This paper is a valuable contribution to the understanding of the dynamic behaviour of steel tube RPC. The SHPB tests provide reliable data on the stress-strain behaviour at high strain rates, and the proposed ultimate strength method is a practical tool for design.

For the design of protective structures, the paper provides important insights into the trade-off between strength and ductility. The steel tube wall thickness is a key design parameter that should be optimised based on the specific loading conditions and the required performance.

The paper also highlights the importance of understanding the dynamic behaviour of composite materials. The static properties are not sufficient for design under impact loading, and the strain rate effect must be considered. The proposed method for incorporating the strain rate effect into the ultimate strength calculation is a step in the right direction, but more research is needed to refine the method and to validate it against full-scale tests.

In conclusion, this paper is a useful reference for engineers involved in the design of protective structures and for researchers working on the dynamic behaviour of composite materials. It provides valuable experimental data and a practical design method, and it identifies the key parameters that affect the performance of steel tube RPC under impact loading. The paper should be read by anyone who is responsible for the design of blast-resistant or impact-resistant structures, and its findings should be incorporated into design guidelines and standards. The industry needs more research in this area, particularly on the effect of the steel tube-RPC interface, on the scale effect, and on the long-term durability of the composite material. The development of steel tube RPC as a protective material is a promising area of research, and this paper provides a solid foundation for future work. The proposed ultimate strength method should be validated with more experimental data, and it should be refined to reduce the relative error. The findings of this paper have direct value for the design of protective structures, and they should be communicated to the engineering community through design guidelines and training.