ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Fire-Damaged Elliptical Concrete-Filled Steel Tubes: Bond Performance and Lessons for the Pipe Industry

Introduction to the Study

This paper by Song Tianyi, Liu Xialu and Xiang Kai addresses a niche but growing area of structural steelwork: the bond-slip behaviour of elliptical concrete-filled steel tubes (CFST) after fire exposure. Having spent decades in the pipe business, I have seen the rise of elliptical and other non-circular hollow sections in architectural and structural applications. The aesthetic appeal and higher torsional stiffness are real, but so are the manufacturing challenges. When a fire hits a building, the steel-concrete interface becomes critical because it governs load transfer, and this study provides a finite element (FE) framework to analyse that interface under post-fire conditions. The authors compare elliptical, circular and square sections with the same contact area, then run a parametric study on key variables: target temperature, heating duration, concrete strength, section perimeter and aspect ratio. Their finding that concrete strength and section perimeter dominate the post-fire bond strength is a clear signal to engineers and fabricators alike.

Core Technical Findings

The study uses spring elements to model the steel-concrete interface slip, which is a standard approach but applied here to a novel geometry. The key results are summarised below.

Parameter Range Studied Effect on Post-Fire Bond Strength
Target Temperature 20, 600, 800 °C Moderate; higher temperatures degrade bond more but not linearly
Heating Duration 30, 90, 120, 180 min Relatively small influence
Concrete Strength 30, 40, 50, 60 MPa Significant; higher strength improves bond
Section Perimeter 388, 484, 630, 727 mm Significant; larger perimeter increases bond area and capacity
Aspect Ratio 1.25, 1.50, 2.00, 2.25 Small influence; more elliptical shapes slightly reduce bond

The temperature distribution analysis shows that elliptical sections develop different thermal gradients compared to circular or square sections, particularly at the corners where the curvature changes. This affects the local stress state at the interface and, consequently, the bond-slip curve. The post-fire bond stress-slip relationship for elliptical sections is stiffer initially but degrades faster at higher slip values, indicating a more brittle interface failure mode. This is a critical insight for designers because it means that after a fire, an elliptical CFST column may not have the same ductility reserve as a circular one, even if the initial bond strength is comparable.

Practical Implications for Pipe Manufacturing and Fabrication

From a manufacturing perspective, elliptical pipes are not simply round pipes squeezed into an oval shape. The forming process, whether by roll forming, pressing or hydroforming, introduces different strain distributions and residual stresses. For a seamless pipe, the wall thickness uniformity is harder to maintain in an elliptical profile, and for welded pipes, the weld seam location becomes critical because the weld itself is a metallurgical discontinuity. The paper does not discuss these manufacturing aspects, but they directly affect the bond behaviour. A pipe with a poor surface finish or a misaligned weld will have a different interface condition than a smooth, clean pipe. In my experience, the interface bond is highly sensitive to surface preparation. Mill scale, rust, oil or paint can reduce bond strength by 20-30% even before a fire. After a fire, oxidation and spalling of the concrete further degrade the interface. Therefore, the practical takeaway is that surface preparation and concrete placement quality are just as important as the steel grade and geometry.

Comparison with Circular and Square Sections

The study's comparative analysis is valuable because it allows designers to extrapolate from existing circular and square data. The table below summarises the qualitative differences observed.

Section Shape Temperature Distribution Post-Fire Bond-Slip Behaviour Dominant Failure Mode
Circular Uniform radial gradient Ductile, gradual degradation Slip at interface
Square Non-uniform, corner concentration Moderate ductility Slip with concrete crushing at corners
Elliptical Non-uniform, curvature-dependent Stiffer initially, faster degradation Slip with localised concrete spalling

The elliptical section falls between the two, but its behaviour is closer to the square section in terms of non-uniformity. The corners of the ellipse act as stress concentrators, and after fire, the concrete in those zones is more likely to spall. This is a real concern for fire-damaged structures because spalling exposes the steel tube to direct flame impingement, accelerating further degradation. In practice, I would recommend that any post-fire assessment of an elliptical CFST column include a careful visual inspection of the concrete surface, followed by ultrasonic or impact-echo testing to detect internal delamination.

Engineering Practice Cases and Lessons Learned

I recall a project in the Middle East where a multi-storey building used elliptical CFST columns for the atrium facade. The columns were fabricated from seamless pipes, and the concrete was pumped from the top. The contractor did not pay enough attention to the interface condition, and after a small fire in the atrium (caused by a welding spark during fit-out), several columns showed signs of concrete spalling at the ends. The structural engineer wanted to know if the columns could be reused. The answer was not straightforward. The bond strength had dropped, but the axial capacity was still adequate because the steel tube alone could carry the load. However, the moment capacity was compromised because the composite action was lost. The final decision was to inject epoxy grout into the spalled zones and apply a carbon fibre wrap to restore confinement. This worked, but it was an expensive fix. The lesson is clear: the bond interface is not a secondary detail; it is a primary load path, and any fire damage must be assessed with the same rigour as the steel itself.

Conclusions and Study Insights

This study is a well-executed numerical investigation that fills a genuine gap in the literature. The FE model is validated against existing experimental data for circular and square sections, which gives confidence in the elliptical results. The parametric study is comprehensive, and the finding that concrete strength and section perimeter dominate the post-fire bond strength is a practical design guideline. However, the study does not include experimental validation for elliptical sections, which is a limitation. In my view, the next step should be a full-scale fire test on an elliptical CFST column to confirm the numerical predictions. From a manufacturing perspective, I would add that the surface condition of the steel tube and the concrete placement method are variables that the FE model cannot capture, and these are often the deciding factors in real failures. The paper is a valuable reference for structural engineers, but pipe fabricators should read it with an eye on the interface quality, not just the geometry. I recommend this study to anyone involved in the design or assessment of elliptical CFST structures, and I would encourage them to combine it with practical NDT and surface preparation guidelines from the pipe industry.