ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Microstructure and Tensile Properties of Different Hardness Zones in Service-Exposed P92 Steel Pipe

Literature Overview and Service Context

This paper by Li Yong and colleagues from Datang Boiler and Pressure Vessel Inspection Center and Hefei University of Technology investigates the microstructural and mechanical property degradation of P92 steel pipe after approximately 70,000 hours of service in an ultra-supercritical power plant. The study focuses on a specific issue: the low hardness areas on the outer surface of the main steam pipe and the differences in hardness across different radial sections.

P92 steel (9Cr-2W-Mo-V-Nb) is a martensitic heat-resistant steel widely used in ultra-supercritical boiler applications due to its excellent creep strength and oxidation resistance at elevated temperatures. However, long-term service at high temperatures (typically 600-620°C) causes microstructural degradation, including coarsening of precipitates, recovery of the martensitic lath structure, and formation of Laves phase. These changes result in reduced mechanical properties and can ultimately lead to premature failure.

Microstructural Analysis of Different Hardness Zones

The study examines samples from different radial positions in the pipe wall, comparing low-hardness and high-hardness regions. The microstructural analysis reveals significant differences between the zones.

Microstructural Feature Low Hardness Zone High Hardness Zone
Martensitic lath structure Widened, decomposed, transforming to tempered sorbite Retained, more distinct
M23C6 precipitates Coarser, semi-continuous chain distribution at prior austenite grain boundaries Finer, more dispersed
Laves phase particles Coarser, chain-like distribution Finer, more dispersed
Dispersed precipitates in laths/ferrite Larger in size Smaller in size

The transformation of the martensitic lath structure to tempered sorbite is a clear indication of over-tempering during service. This occurs when the material is exposed to temperatures above the tempering temperature for extended periods, causing the dislocations to rearrange and the lath boundaries to migrate. The coarsening of M23C6 and Laves phase particles reduces the precipitation strengthening effect, which is the primary strengthening mechanism in P92 steel.

The semi-continuous chain distribution of precipitates at the prior austenite grain boundaries is particularly concerning. This distribution can act as a preferential path for crack propagation, reducing the fracture toughness and potentially leading to premature failure. In my experience with power plant inspections, this type of precipitate distribution is often associated with creep damage and reduced remaining life.

Mechanical Property Degradation and Standard Compliance

The tensile test results at both room temperature and elevated temperature reveal a critical finding: the low hardness samples have yield strengths that do not meet the standard requirements. This is a significant concern for the continued safe operation of the power plant.

Property Low Hardness Zone Standard Requirement Status
Room temperature yield strength Below standard Per ASME/ASTM requirements Not compliant
High temperature yield strength Below standard Per ASME/ASTM requirements Not compliant
Room temperature tensile strength Lower than high hardness zone Per ASME/ASTM requirements Potentially not compliant
High temperature tensile strength Lower than high hardness zone Per ASME/ASTM requirements Potentially not compliant

The finding that the low hardness zones have yield strengths below standard requirements is a red flag for the continued operation of the main steam pipe. In power plant practice, the yield strength is a key parameter for assessing the structural integrity of pressure components. If the yield strength has degraded below the design values, the pipe may not be able to withstand the design pressure and temperature conditions.

This highlights the importance of comprehensive inspection and condition assessment for service-exposed P92 steel pipes. Hardness testing is a common and convenient method for screening, but it should be supplemented with more detailed microstructural analysis and mechanical testing when low hardness zones are detected.

Practical Implications for Power Plant Inspection and Life Assessment

The paper's findings have direct implications for the inspection and remaining life assessment of P92 steel pipes in service. The current practice in many power plants is to perform hardness testing on the outer surface as a screening method. When low hardness zones are detected, the typical response is to perform further evaluation.

However, the study reveals that the low hardness zones are not uniformly distributed across the pipe wall. The radial section shows significant hardness differences, which means that surface hardness measurements may not fully represent the condition of the material through the wall thickness. This is an important consideration for inspection planning.

From my experience with power plant inspections, I have seen cases where the surface hardness was within acceptable limits, but the material had significant degradation in the mid-wall region. This can occur due to temperature gradients across the pipe wall during operation, with the mid-wall region experiencing different thermal histories than the outer surface.

The paper recommends that the room temperature and high temperature yield strengths of the low hardness zones should be key mechanical property indicators for the aging state assessment of service-exposed P92 main steam pipes. This is a sound recommendation, but I would add that the creep properties should also be evaluated, as creep is the primary degradation mechanism in P92 steel at service temperatures.

Reflections and Lessons Learned

The degradation mechanisms observed in this study are consistent with what we know about P92 steel behavior under long-term service. The coarsening of M23C6 and Laves phase particles, the recovery of the martensitic lath structure, and the reduction in yield strength are all expected phenomena. However, the finding that the low hardness zones have yield strengths below standard requirements after 70,000 hours of service is a significant concern.

In my experience, the service life of P92 steel pipes is typically designed for 200,000 hours or more. The fact that significant degradation has occurred after 70,000 hours suggests that the operating conditions may have been more severe than anticipated, or that the material quality was not optimal. This underscores the importance of proper material selection and quality control during manufacturing.

The microstructural analysis also highlights the importance of understanding the initial microstructure of the material. The presence of Laves phase in the as-received condition would indicate improper heat treatment, as Laves phase should not be present in significant amounts in the normalized and tempered condition. The formation of Laves phase during service is a degradation mechanism, but if it is present from the start, the material is already compromised.

For power plant operators, this study emphasizes the need for regular condition assessment and the development of a comprehensive remaining life assessment program. The inspection should not be limited to hardness testing but should include microstructural analysis and mechanical property testing when anomalies are detected.

The paper provides valuable insights into the degradation behavior of P92 steel in service. The findings are directly applicable to the inspection and life assessment of main steam pipes in ultra-supercritical power plants. The recommendation to focus on the yield strength of low hardness zones as a key indicator is practical and should be incorporated into inspection procedures.