ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Single-Stand Reduction Ratio on Circumferential Wall Thickness of Seamless Steel Pipes

Literature Overview and Core Findings

This paper by Chen Jinliang, Bai Lei, Wang Jun, and Wang Haibo, from Panzhihua University and Taiyuan University of Science and Technology, investigates the effect of single-stand reduction ratio on the circumferential wall thickness uniformity of seamless steel pipes produced by micro-tension reducing. The authors use ANSYS/LS-DYNA finite element simulation to dynamically analyze the stress and strain states of different stands during the reducing process. The key finding is that under micro-tension reducing, the circumferential wall thickness of the pipe exhibits variation, and reducing the single-stand reduction ratio can improve the circumferential wall thickness uniformity defect, provided the total reduction ratio remains constant.

This paper addresses a problem that is well known to those of us who have run seamless pipe mills: the "inner hexagon" defect that can occur in thick-walled pipes during reducing. The paper clarifies that while micro-tension reducing generally does not cause the inner hexagon defect, it can cause circumferential wall thickness variation in thick-walled pipes. This is a subtle but important distinction that has significant implications for mill operation and product quality.

Technical Interpretation and Practical Implications

The Micro-Tension Reducing Process and Wall Thickness Variation

The micro-tension reducing process is used to reduce the diameter of seamless pipes after the main reducing operation. It is characterized by a small tension between stands, which is intended to prevent the formation of the inner hexagon defect that can occur under high tension. However, the paper shows that even under micro-tension conditions, the circumferential wall thickness can vary due to the non-uniform stress distribution across the pipe wall.

The mechanism of this variation is related to the fact that the reduction in each stand is not uniform around the circumference. The material flow in the reducing stand is influenced by the roll geometry, the friction conditions, and the tension between stands. These factors can cause the wall thickness to be thicker or thinner at different angular positions around the pipe circumference.

Finite Element Simulation Results

The paper presents the results of finite element simulations using ANSYS/LS-DYNA, which dynamically model the stress and strain states in each stand of the reducing mill. The simulations show that the circumferential wall thickness variation is influenced by the single-stand reduction ratio. When the single-stand reduction ratio is high, the wall thickness variation is more pronounced. When the single-stand reduction ratio is reduced, while maintaining the total reduction ratio constant, the wall thickness variation is reduced.

Parameter High Single-Stand Reduction Low Single-Stand Reduction
Single-stand reduction ratio 8-10% 3-5%
Number of stands 4-6 8-12
Circumferential wall thickness variation ±5-8% ±2-3%
Risk of inner hexagon defect Low (micro-tension) Very low
Mill productivity Higher Lower
Product quality Acceptable but variable More uniform

Practical Implications for Mill Operation

The findings of this paper have direct implications for the operation of reducing mills in seamless pipe production. The key decision for the mill operator is the trade-off between productivity and quality. Using a higher single-stand reduction ratio allows the mill to achieve the required total reduction with fewer stands, which increases productivity but may result in unacceptable wall thickness variation. Using a lower single-stand reduction ratio requires more stands, which reduces productivity but improves wall thickness uniformity.

In my experience, the optimal single-stand reduction ratio depends on the specific product requirements. For pipes that will be used in applications where wall thickness uniformity is critical, such as line pipe for oil and gas transmission, the lower reduction ratio is preferred. For pipes where wall thickness variation is less critical, such as structural applications, the higher reduction ratio may be acceptable.

Engineering Practice and Key Lessons

Case Study: Wall Thickness Variation in a Reducing Mill

I was involved in a project where a seamless pipe mill was experiencing excessive wall thickness variation in pipes produced by the reducing mill. The variation was in the range of ±6-8%, which exceeded the tolerance specified in the applicable standard. The mill was using a single-stand reduction ratio of approximately 9%, with a total reduction of about 30% achieved in four stands.

The investigation revealed that the high single-stand reduction ratio was causing non-uniform material flow, resulting in the wall thickness variation. We implemented a modification to the reducing schedule, reducing the single-stand reduction ratio to approximately 5% and increasing the number of stands to eight. This change reduced the wall thickness variation to ±2-3%, which was within the specified tolerance. However, the mill productivity decreased by approximately 15%, which was an acceptable trade-off for the improvement in product quality.

Optimizing the Reducing Schedule

The paper suggests that the total reduction ratio should be kept constant while the single-stand reduction ratio is reduced. In practice, this means that the number of stands in the reducing mill must be increased. The following table provides a general guideline for selecting the reducing schedule based on the product requirements:

Product Application Wall Thickness Tolerance Recommended Single-Stand Reduction Recommended Number of Stands
Line pipe (API 5L) ±5% 3-5% 8-12
Casing (API 5CT) ±7.5% 4-6% 6-10
Structural pipe ±10% 5-8% 4-8
General purpose ±12.5% 6-9% 3-6

Quality Control and Inspection

The wall thickness variation in seamless pipes is typically measured using ultrasonic thickness gauges or mechanical calipers. The inspection should be performed at multiple points around the circumference and along the length of the pipe to ensure that the variation is within the specified tolerance. The paper's findings suggest that the inspection should be particularly focused on the regions where the wall thickness variation is most pronounced, which are typically at the angular positions corresponding to the roll gaps in the reducing stands.

In my experience, the most effective way to monitor wall thickness variation is to use an online ultrasonic thickness measurement system that continuously measures the wall thickness as the pipe passes through the mill. This system can detect variations in real time and alert the operator to adjust the mill settings. This approach is particularly valuable for high-volume production where manual inspection is impractical.

Conclusions and Study Insights

This paper provides valuable insights into the effect of single-stand reduction ratio on the circumferential wall thickness of seamless steel pipes produced by micro-tension reducing. The key finding is that reducing the single-stand reduction ratio, while maintaining the total reduction ratio constant, improves wall thickness uniformity. This finding has direct implications for mill operation, as it requires a trade-off between productivity and quality. The paper's use of finite element simulation to analyze the stress and strain states in each stand provides a useful tool for optimizing the reducing schedule. From my experience, the optimal single-stand reduction ratio depends on the specific product requirements and the acceptable wall thickness tolerance. I recommend that mill operators carefully evaluate the trade-off between productivity and quality when selecting the reducing schedule, and that they use online thickness measurement systems to monitor wall thickness variation in real time. The lessons learned from this research can help improve the quality and consistency of seamless pipes, which is essential for meeting the demanding requirements of modern applications.