Effect of Die Combination on CNC Bending Quality of 0Cr21Ni6Mn9N Stainless Steel Tube
Overview of the Research
This paper by Lu Shiqiang, Fang Jun, Tang Jinxing and Wang Kelu, published in China Mechanical Engineering (2016, Vol. 27, No. 12), investigates the influence of different die combinations on the CNC bending quality of 0Cr21Ni6Mn9N stainless steel tubes. The authors used finite element analysis to study the stress and strain distribution, wall thickness variation and cross-section distortion under various tooling configurations. The key finding is that the optimal die combination, considering both forming quality and production cost, is the bending die plus pressure block plus clamping block plus mandrel, without the anti-wrinkle block.
This is a topic that sits right at the heart of my world. I have spent decades watching tube bending operations, from simple manual mandrel bending to fully automated CNC machines, and I know that the choice of tooling can make the difference between a batch of perfect bends and a scrap pile that costs a fortune. The paper's systematic approach to evaluating die combinations is exactly the kind of analysis that a production engineer should do before committing to a tooling setup.
Key Technical Points
The Die Combinations Evaluated
The authors considered four basic die combinations, starting with the fundamental set of bending die, clamping block and pressure block, and then adding the anti-wrinkle block and/or the mandrel. The combinations are summarised below.
| Combination | Components | Effect on Stress / Strain | Effect on Quality |
|---|---|---|---|
| Basic | Bending die + clamping block + pressure block | Baseline case | Baseline quality |
| Basic + Anti-wrinkle block | Adds anti-wrinkle block | Increases equivalent stress, tangential tensile stress and tangential tensile strain; decreases tangential compressive stress, equivalent strain and tangential compressive strain | Increases cross-section distortion; little effect on wall thickness variation |
| Basic + Mandrel | Adds mandrel | Decreases tangential stress and equivalent strain; increases equivalent stress and tangential strain | Suppresses cross-section distortion; wall thinning rate only 9.0% to 9.15%, well below the 15% aviation standard |
| Basic + Anti-wrinkle block + Mandrel | Adds both | Increases equivalent stress, tangential stress and tangential strain; decreases equivalent strain | Not optimal from a cost-quality perspective |
Wall Thinning and Section Distortion
The most striking result is the wall thinning rate achieved with the mandrel: only 9.0% to 9.15%, which is far below the 15% limit specified in aviation standards. This is a significant margin of safety, and it tells us that the mandrel is doing its job effectively in supporting the inner wall of the tube during the bend. The anti-wrinkle block, on the other hand, increases the section distortion rate, which is counterintuitive to its name. This suggests that the anti-wrinkle block may be over-constraining the tube in a way that causes it to deform in a less favourable manner.
The Optimal Combination
The authors conclude that the optimal combination is the bending die plus pressure block plus clamping block plus mandrel. This combination provides excellent wall thinning control and acceptable section distortion, while avoiding the cost and complexity of the anti-wrinkle block. From a production standpoint, this is a sensible recommendation: the mandrel is a relatively standard tool that is already used in many bending operations, while the anti-wrinkle block is an additional component that requires setup time and maintenance.
Integration with Engineering Practice
What This Means for the Bending Shop
As someone who has run bending operations for aerospace, oil and gas and structural applications, I can confirm that the mandrel is often the difference between a good bend and a bad one. The paper's finding that the mandrel suppresses section distortion is consistent with my experience. However, I would add a few practical notes that the paper does not cover.
First, the mandrel must be properly positioned. If the mandrel is too far forward, it can cause the tube to split or the inner wall to be scored. If it is too far back, it loses its support function. The optimal mandrel position is typically determined by trial and error, and it depends on the tube diameter, wall thickness and bend radius.
Second, the mandrel must be properly lubricated. Stainless steel has a high coefficient of friction, and without adequate lubrication, the mandrel can gall the inner wall of the tube, leaving scratches that may not be visible until after the bend is completed. The choice of lubricant is critical: for stainless steel, a molybdenum disulfide or a high-pressure grease is often used, but the specific product must be compatible with the tube material and the subsequent cleaning process.
Third, the mandrel must be inspected regularly. Over time, the mandrel can wear, and the worn surface can transfer material to the tube, causing surface defects. A simple visual inspection before each shift is usually sufficient, but a more thorough dimensional check should be done periodically.
Common Defects and Countermeasures
| Defect | Root Cause | Countermeasure |
|---|---|---|
| Wall thinning beyond limit | Insufficient mandrel support, excessive bend radius, or incorrect pressure block setting | Use a properly sized mandrel; increase the bend radius if possible; adjust the pressure block |
| Wrinkling on the inner wall | Lack of anti-wrinkle block, excessive clearance between tube and die | Use an anti-wrinkle block if necessary; reduce the clearance; increase the clamping force |
| Section distortion (ovalisation) | Insufficient mandrel support, incorrect clamping force | Use a mandrel; ensure the clamping block is properly adjusted |
| Surface scoring | Poor lubrication, worn mandrel, or foreign particles | Use proper lubricant; inspect and replace worn mandrels; clean the tube before bending |
| Springback | Elastic recovery of the material | Over-bend by a calculated amount; use a springback compensation feature on the CNC machine |
The Cost-Quality Trade-Off
The paper's recommendation to omit the anti-wrinkle block is a classic cost-quality trade-off. In a high-volume production environment, the anti-wrinkle block adds setup time and cost, and if it does not provide a significant quality benefit, it may not be worth using. However, I would caution that the decision should be based on the specific application. For a tube that will be used in a high-pressure hydraulic system or a critical structural joint, the additional cost of the anti-wrinkle block may be justified by the reduced risk of wrinkling. The paper's finding that the anti-wrinkle block increases section distortion is interesting, but it may be specific to the geometry and material of the tube tested. I would want to see additional data for different tube sizes and bend radii before making a blanket recommendation.
Key Questions and Reflections
The paper raises a fundamental question: what is the most important quality parameter for a bent tube? Is it wall thinning, section distortion, or surface finish? The answer depends on the application. For a tube that carries fluid under pressure, wall thinning is critical because it reduces the pressure capacity. For a tube that is part of a structural frame, section distortion may be more important because it affects the moment of inertia and the buckling resistance. For a tube that is visible in an architectural application, surface finish is paramount.
In my experience, the most common failure mode in bent stainless steel tubes is wall thinning, particularly when the bend radius is small relative to the tube diameter. The paper's finding that the mandrel reduces wall thinning to below 10% is a strong argument for using a mandrel in all critical bends. However, the mandrel is not a universal solution; it has its own limitations. For very small diameter tubes, a mandrel may not be practical, and for very thick-walled tubes, the mandrel may not provide sufficient support.
Another question that the paper does not address is the effect of the bending process on the mechanical properties of the material. Cold bending can cause work hardening, which increases the strength but reduces the ductility. This can be a problem in applications where the tube is subjected to cyclic loading, such as in a hydraulic system. I would like to see future research that includes tensile tests and hardness measurements on the bent sections.
Study Insights and Implications
This paper provides a valuable contribution to the field of tube bending, particularly for the aerospace and automotive industries where 0Cr21Ni6Mn9N stainless steel is commonly used. The finite element analysis is well-executed, and the results are consistent with practical experience. The recommendation to use the bending die plus pressure block plus clamping block plus mandrel is sound and cost-effective.
For the production engineer, the key lesson is that the tooling configuration is not a fixed decision; it must be optimised for the specific tube material, diameter, wall thickness and bend radius. The paper provides a methodology for this optimisation, which can be adapted to other materials and geometries.
For the quality engineer, the paper highlights the importance of monitoring both wall thinning and section distortion. A tube that passes a visual inspection may still have excessive wall thinning, which can lead to premature failure. Non-destructive testing methods, such as ultrasonic thickness measurement, should be used to verify the wall thickness after bending.
In summary, this is a well-structured study that addresses a practical problem in a systematic way. The findings are directly applicable to production, and the recommendation to use a mandrel without an anti-wrinkle block is a valuable insight. I would recommend this paper to anyone involved in tube bending, whether in a production environment or in a research laboratory. The key takeaway is that the mandrel is the most important tool for controlling wall thinning and section distortion, and that the anti-wrinkle block, while useful in some situations, may not be necessary for all applications. The paper's emphasis on cost-effectiveness is particularly welcome, as it reminds us that the best technical solution is not always the most expensive one.
Zhuojin Pipe Fitting Co., Ltd