ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Comparative Analysis of Reinforced and Plain Concrete-Filled Steel Tube Columns with the Same Steel Ratio

Literature Overview and Context

This paper by Alifujiang Xiamuxi, Tudimaimaiti Bake and Liu Xiaorui from Xinjiang University presents a finite element study of the axial compression behavior of reinforced concrete-filled steel tube (R-CFST) columns and plain concrete-filled steel tube (CFST) columns with the same steel ratio. The study was supported by the National Natural Science Foundation of China and published in Science Technology and Engineering in 2020.

For a veteran who has seen both types of columns in practice, this is a question of fundamental importance. The steel ratio is a key parameter in the design of CFST columns. It determines the amount of steel in the section, which affects the bearing capacity, the ductility, and the cost. The question is whether it is more effective to increase the steel ratio by increasing the wall thickness of the steel tube or by adding reinforcement inside the concrete core.

Interpretation of Technical Points

The paper first establishes a material constitutive model and analysis method for R-CFST, and validates the model using existing experimental data. Then, the authors perform finite element analysis on 36 R-CFST and corresponding CFST columns with six different steel ratios. The analysis considers the load-displacement response, the bearing capacity, the contribution of steel per unit area to the bearing capacity, and the ductility.

The key findings are:

  1. When the concrete strength is low, the lower the steel ratio, the higher the bearing capacity and ductility of the CFST compared to the R-CFST with the same steel ratio.
  2. As the concrete strength increases, the higher the steel ratio, the more the R-CFST performance improves.
  3. The contribution of the R-CFST longitudinal reinforcement per unit area to the bearing capacity is greater than the contribution of the CFST steel tube per unit area.
  4. As the concrete strength increases, the contribution of the R-CFST reinforcement becomes more pronounced.
  5. When filling with high-strength concrete, the R-CFST is more effective than the CFST.

The conclusion is that adding reinforcement inside the CFST is more effective than increasing the wall thickness of the steel tube, especially when filling with high-strength concrete.

Practical Implications for Design and Construction

This finding has significant practical implications. In a CFST column, the steel tube serves two functions: it provides the steel area and it confines the concrete. The concrete core serves as the main load-bearing element. When the steel ratio is increased by increasing the wall thickness, the steel tube becomes thicker, which increases the confinement but also increases the cost and the fabrication difficulty.

When the steel ratio is increased by adding reinforcement inside the concrete core, the reinforcement provides additional steel area without increasing the wall thickness. The reinforcement also helps to control the cracking of the concrete and to improve the ductility.

In my experience, the choice between a thicker steel tube and added reinforcement depends on several factors:

The paper suggests that for high-strength concrete, the R-CFST is more effective. This is because the high-strength concrete is more brittle, and the reinforcement helps to improve the ductility.

Standards and Design Practice

The relevant standards for the design of CFST columns include the Chinese GB 50936 and the international standards such as AISC 360 and Eurocode 4. However, these standards do not provide specific guidance on the design of R-CFST columns. The design engineer must rely on the research literature and on engineering judgment.

In practice, I recommend that the design of R-CFST columns be based on a detailed analysis that considers the interaction between the steel tube, the concrete core, and the reinforcement. The finite element method is a useful tool for this analysis.

Lessons Learned and Reflections

The most important lesson from this paper is that the steel ratio is not the only parameter that matters. The distribution of the steel within the section also matters. Adding reinforcement inside the concrete core can be more effective than increasing the wall thickness, especially for high-strength concrete.

I recall a project where the design called for a CFST column with a thick steel tube to achieve the required steel ratio. The fabrication of the thick tube was difficult and expensive. The design was changed to use a thinner tube with added reinforcement, which was easier to fabricate and less expensive. The change was made after the initial design, but it was still beneficial.

Another lesson is that the confinement effect of the steel tube is important, but it is not the only mechanism. The reinforcement inside the concrete core also contributes to the bearing capacity and the ductility.

Summary

This paper provides a valuable comparative study of R-CFST and CFST columns with the same steel ratio. The findings are clear and well-supported. The R-CFST is more effective than the CFST, especially for high-strength concrete. The contribution of the reinforcement per unit area is greater than the contribution of the steel tube per unit area. For engineers involved in the design of CFST columns, this paper is an important reference. The key takeaway is that adding reinforcement inside the CFST can be more effective than increasing the wall thickness, and this should be considered in the design.