ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Rectangular Concrete-Filled Steel Tube Large-Span Cantilever Trusses: Experimental Study on Structural Behaviour

Literature Overview and Relevance

This paper from South China University of Technology and Foshan University of Science and Technology addresses a specific structural challenge: how to design large-span cantilever trusses that are both light and stiff. The authors propose using rectangular concrete-filled steel tube (CFT) members for the chords and web members, arguing that this configuration fully exploits the composite action between steel and concrete. They tested two large-scale truss models, one with CFT members and one with hollow steel members, and compared the failure modes, deformation characteristics, and load capacities. This is the kind of comparative testing that provides clear design guidance, and the results are directly applicable to large-span structures such as stadium roofs, airport terminals, and bridge cantilevers.

Core Technical Points and Findings

Improved Stiffness and Reduced Deformation

The CFT truss specimens showed increased stiffness and reduced deformation compared to the hollow steel truss. This is the expected benefit of composite action, but the magnitude of the improvement is what matters. The authors report that the CFT truss had higher ultimate load capacity and that the concrete filling effectively prevented local buckling of the steel tube walls. This is a critical finding because local buckling is often the limiting factor in hollow steel trusses with slender members.

Failure Controlled by Material Strength

The authors found that the CFT truss specimens failed by material strength rather than by local buckling or instability. This is the ideal failure mode because it means the full capacity of the steel and concrete is utilised. In contrast, hollow steel trusses often fail by local buckling before the material reaches its yield strength, wasting capacity.

Joint Moments and Their Influence

The authors highlight that the joint moments at the connections between web members and chords are significant and cannot be ignored in design. This is a practical issue that is often underestimated in truss design, where joints are sometimes assumed to be pinned. The direct welding connection used in the test specimens creates semi-rigid joints with significant moment capacity, but also with significant stress concentrations. The design must account for these moments to avoid premature joint failure.

Engineering Practice Insights

Manufacturing Considerations

The rectangular CFT truss requires precise fabrication of the rectangular tubes and careful welding of the web members to the chords. The following manufacturing controls are critical:

Parameter Specification Inspection Method
Rectangular tube dimensions Width and height tolerance ±1 mm Caliper and micrometer
Tube wall thickness Tolerance ±0.5 mm Ultrasonic thickness gauge
Web member cut length Tolerance ±1 mm Tape measure
Weld quality Full penetration for load-bearing welds UT or RT
Joint preparation Proper bevel and gap Visual inspection

The Challenge of Concrete Filling

Filling rectangular tubes with concrete is more difficult than filling round tubes because the corners create areas where concrete may not flow easily. The authors used a filling method that worked in the laboratory, but on site, the concrete must be placed carefully with vibration to ensure complete filling. I would recommend using self-compacting concrete with a maximum aggregate size of 10 mm to ensure flow into the corners.

Site Erection

The CFT truss is heavier than a hollow steel truss, so lifting and erection must be planned carefully. The truss should be lifted from the top chord with a spreader beam to avoid bending stresses. The joints between the truss and the supporting structure must be designed to transfer the full load, and the concrete filling should be done before erection to avoid the risk of concrete spalling during lifting.

Quality Control and Inspection

Inspection Item Method Acceptance Criteria
Rectangular tube dimensions Caliper and micrometer Width and height ±1 mm
Weld integrity UT or RT No defects exceeding code acceptance criteria
Concrete fill quality Ultrasonic pulse velocity No voids >5% of cross-section
Joint moment capacity Strain gauge measurement Within ±10% of design value
Truss deflection Laser survey Within design tolerance

Reflections and Study Insights

The finding that CFT trusses fail by material strength rather than local buckling is a powerful argument for using this system in large-span structures. In my experience, local buckling is the most common failure mode in hollow steel trusses, and it often occurs at loads well below the theoretical capacity. The concrete filling eliminates this problem, allowing the full material strength to be utilised.

The joint moments are a critical design consideration that is often overlooked. In my experience, many truss failures have occurred at the joints, not in the members, because the joint moments were not properly accounted for. The authors' warning that joint moments cannot be ignored is a valuable reminder for design engineers.

Reference Value and Outlook

This paper provides a solid experimental basis for the design of rectangular CFT trusses, but the limited number of test specimens (two) means that the results should be validated against a larger database before being adopted in design codes. The next steps should include dynamic loading tests, fatigue behaviour, and the effect of joint details on the overall performance.

From a manufacturing standpoint, the rectangular CFT truss is more expensive to produce than a hollow steel truss due to the concrete filling and the additional handling. However, for large-span structures where weight and stiffness are critical, the additional cost may be justified by the improved performance and reduced structural depth.

In my judgment, this is a valuable contribution to the field of large-span structural design. The comparative testing between CFT and hollow steel trusses provides clear design guidance, and the finding that CFT trusses fail by material strength is a powerful argument for their use. I would recommend this paper to any engineer working on large-span structures, and I would encourage further research on the long-term behaviour of rectangular CFT members under cyclic loading and environmental exposure. The construction industry needs more solutions that combine the lightness of steel with the stiffness of concrete, and this paper is a step in the right direction.