ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Full-Scale Square Steel Tube High-Strength Recycled Concrete Columns: Axial Compression Test and Design Implications

Overview of the Study

Niu Haicheng and colleagues from Beijing University of Technology and Henan Polytechnic University conducted full-scale axial compression tests on three square steel tube columns filled with high-strength concrete. The three specimens had identical geometric dimensions but differed in concrete type and internal construction: Specimen 1 used high-strength normal concrete, Specimen 2 used high-strength recycled concrete, and Specimen 3 used high-strength recycled concrete with an internal steel cage. The loading was applied in a single-direction repeated loading and unloading pattern. The study analysed failure characteristics, bearing capacity, energy dissipation, ductility, and stiffness, and compared the results with five international design codes.

This study is directly relevant to the pipe industry because square steel tubes are manufactured differently from round tubes, and the manufacturing process affects the tube's performance in composite columns. The use of recycled concrete is also a sustainability trend that has implications for the steel-concrete interface.

Technical Interpretation: Square Tube Geometry and Stress Distribution

Square steel tubes have a different stress distribution than round tubes under axial compression. The flat sides of the square tube are less effective at confining the concrete than the curved surface of a round tube. The corners of the square tube are stress concentrations, and the flat sides may buckle outward under high loads.

From a manufacturing perspective, square tubes are typically formed from steel plate by cold forming (roll forming or press bending) and then welded at the corner. The welding process is critical. If the corner weld is not full penetration, the tube may fail prematurely at the corner. The corner radius also affects the stress distribution: a sharp corner (small radius) creates higher stress concentrations than a rounded corner.

Parameter Round Tube Square Tube
Confinement efficiency Higher Lower
Stress concentration Uniform High at corners
Manufacturing route Seamless or welded Cold-formed and welded
Weld location Circumferential or longitudinal Longitudinal at corner
Local buckling resistance Higher Lower at flat sides

The study found that the failure process and failure mode of the square steel tube high-strength recycled concrete columns were similar to those of the square steel tube high-strength normal concrete columns. This suggests that the recycled concrete does not fundamentally change the failure mechanism, but it may affect the ductility and energy dissipation.

Recycled Concrete: The Sustainability Trade-Off

Recycled concrete aggregate (RCA) has lower strength and higher porosity than natural aggregate. This affects the bond between the concrete and the steel tube. The study found that the recycled concrete column had slightly lower bearing capacity than the normal concrete column, but the difference was not dramatic. This is encouraging for sustainability, but the long-term performance of recycled concrete in composite columns needs further investigation.

From a pipe perspective, the interface between the steel tube and the recycled concrete is critical. The recycled concrete may shrink more than normal concrete, which could create a gap at the steel-concrete interface and reduce the confinement effect. The study did not specifically address this, but it is a practical concern.

The study also found that the internal steel cage significantly improved the bearing capacity, ductility, and energy dissipation of the recycled concrete column. This is a practical solution to the reduced performance of recycled concrete. The steel cage provides additional confinement and also acts as a crack arrestor, preventing the concrete from spalling.

Design Code Applicability

The study compared five international design codes and found that the Chinese code CECS 159-2004 (Technical Specification for Concrete-Filled Steel Tubular Structures) provided the best agreement with the test results. This is a useful finding for designers, but it also raises a question: why does the Chinese code perform better than the others?

The answer may lie in the calibration of the code. CECS 159-2004 was developed based on extensive testing of square and rectangular steel tube concrete columns, including high-strength concrete. The other codes, such as Eurocode 4 and AISC 360, were calibrated primarily for round tubes or for normal-strength concrete. This highlights the importance of using codes that are calibrated for the specific application.

From a pipe perspective, the design code should also account for the manufacturing route of the square tube. Cold-formed tubes have residual stresses from the forming process, which may reduce the buckling capacity. The design code should include a reduction factor for cold-formed tubes, or the manufacturing process should be specified to minimise residual stresses.

Engineering Implications and Lessons Learned

The practical implications of this study are significant:

  1. Recycled concrete can be used in square steel tube columns with a modest reduction in capacity. This is a sustainable option that should be considered in projects where recycled aggregate is available.
  2. Internal steel cages improve performance and can offset the reduced capacity of recycled concrete. The cage should be designed to provide adequate confinement and crack arrest.
  3. CECS 159-2004 is applicable for square steel tube high-strength recycled concrete columns. Designers can use this code with confidence, but should verify the concrete properties and the steel tube quality.
  4. Square tube manufacturing quality is critical. The corner weld must be full penetration, and the corner radius should be controlled to minimise stress concentrations.

Concluding Reflection

This study provides valuable data on the axial compression behavior of square steel tube high-strength recycled concrete columns. The finding that recycled concrete can be used with a modest capacity reduction is encouraging for sustainability. The internal steel cage is a practical solution to improve performance. From a pipe industry perspective, the key takeaway is that square tube manufacturing quality is critical for composite column performance. The corner weld must be full penetration, the corner radius must be controlled, and the tube geometry must be consistent. The design code CECS 159-2004 is applicable, but designers should verify the tube manufacturing route and the concrete properties. I would recommend that square steel tubes for composite columns be specified with full penetration corner welds and a controlled corner radius, and that the tube be inspected for weld seam defects before use. The sustainability benefits of recycled concrete should be weighed against the modest capacity reduction, and the internal steel cage should be considered when higher performance is required.