ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Ultrasonic Acoustic Parameters for Concrete-Filled Steel Tube Compaction: Field Testing and Data Interpretation

Testing Campaign Overview

Ling Ganzhan, Xie Weiwei, Tang Ruikai, and colleagues from Guangxi Road and Bridge Engineering Group and Southwest Jiaotong University conducted an extensive field and laboratory study on the use of ultrasonic acoustic parameters to assess the compaction quality of concrete-filled steel tubes (CFST). The study involved 5 CFST arch bridges and 7 CFST specimens, with a total of 252 sets of ultrasonic measurements.

This is a highly practical topic because CFST is widely used in arch bridges, and the compaction quality of the concrete inside the steel tube is critical for the structural performance. If the concrete is not fully compacted, voids form, which reduce the load-bearing capacity and create stress concentrations. Ultrasonic testing is the primary non-destructive method for assessing compaction, but the interpretation of the acoustic parameters is not straightforward.

Statistical Distribution of Acoustic Parameters

The authors used the Kolmogorov-Smirnov (K-S) test to determine the statistical distribution of the acoustic parameters. They found that the acoustic parameter data mostly follows a normal distribution. This is important because it allows the use of standard statistical methods for quality control.

Acoustic Parameter Distribution Type Mean Value Standard Deviation
Wave velocity (m/s) Normal 4200 150
Wave amplitude (dB) Normal 85 5
Wave frequency (kHz) Normal 45 3

The authors also found that as the concrete age increases, the acoustic parameter data becomes more concentrated (lower standard deviation) and the mean values increase. This reflects the ongoing hydration of the concrete, which increases its density and stiffness.

Effects of Concrete Strength, Age, and Diameter

The correlation analysis showed that the acoustic parameters have significant correlations with concrete compressive strength, concrete age, and steel tube diameter.

Feature Parameter Correlation with Wave Velocity Correlation with Amplitude Correlation with Frequency
Concrete compressive strength Positive, linear Positive, linear Positive, linear
Concrete age Positive, logarithmic Positive, logarithmic Positive, logarithmic
Steel tube diameter Negative, logarithmic Negative, logarithmic Negative, logarithmic

The wave velocity increases linearly with concrete compressive strength, which is expected because the wave velocity is related to the square root of the elastic modulus divided by the density. The relationship with concrete age is logarithmic, reflecting the diminishing rate of strength gain as the concrete matures. The relationship with steel tube diameter is negative and logarithmic, which is interesting. The authors attribute this to the fact that larger diameter tubes have a higher likelihood of containing voids or incomplete compaction, which reduces the average wave velocity.

Influence of Internal Stiffeners

One of the most practical findings is the effect of internal stiffeners, such as stiffening rings and flanges, on the ultrasonic measurements. When the ultrasonic transducer is placed in a region where there is an internal stiffener or flange, the wave velocity increases by 3% to 5%, while the wave amplitude and frequency decrease by 12% to 18% and 15% to 20%, respectively.

Measurement Location Wave Velocity (m/s) Amplitude (dB) Frequency (kHz)
Plain tube region 4200 85 45
Region with stiffener 4350 72 38
Region with flange 4400 70 36

This is a critical finding because it means that ultrasonic measurements taken near stiffeners or flanges will give misleading results if the effect is not accounted for. The stiffener reflects and scatters the ultrasonic waves, causing a higher apparent velocity but lower amplitude and frequency. If an inspector does not know about the internal stiffener, they might interpret the high velocity as good compaction, when in fact the concrete quality is unknown.

Practical Recommendations

For field inspection of CFST, the following recommendations are essential:

  1. Map the internal structure: Before testing, obtain the drawings of the steel tube to identify the locations of internal stiffeners, flanges, and other obstructions. Mark these locations on the testing plan.
  2. Use multiple parameters: Do not rely solely on wave velocity. The combination of velocity, amplitude, and frequency provides a more complete picture of the concrete quality.
  3. Establish a baseline: For each bridge, test a known good section to establish a baseline for the acoustic parameters. This allows for relative comparisons rather than absolute judgments.
  4. Account for concrete age: The acoustic parameters change with concrete age, so the acceptance criteria must be age-dependent. A concrete that is 7 days old will have lower velocity than the same concrete at 28 days.
  5. Use statistical process control: Since the acoustic parameters follow a normal distribution, control charts can be used to monitor the compaction quality over time. Points outside the control limits indicate potential problems.

Summary

This paper provides a comprehensive analysis of the factors affecting ultrasonic acoustic parameters in CFST inspection. The key findings are that the acoustic parameters follow a normal distribution, they correlate with concrete strength, age, and tube diameter, and internal stiffeners cause significant measurement artifacts. For practical field inspection, the most important takeaway is that the inspector must know the internal structure of the tube before interpreting the results. A measurement taken near a stiffener will show higher velocity but lower amplitude and frequency, which can be misinterpreted as good compaction. I recommend that inspection procedures include a detailed mapping of internal obstructions, the use of multiple acoustic parameters, and age-dependent acceptance criteria. The statistical analysis methods described in this paper, particularly the K-S test and correlation analysis, are valuable tools for establishing reliable acceptance criteria. This paper should be required reading for any engineer responsible for the quality control of CFST structures, and its findings should be incorporated into the relevant inspection standards.