ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Axial Performance of Square Stainless Steel Tube UHPC Short Columns

Literature Overview

This paper by Tang Hongyuan, Hu Xiaowei, and Liu Ye presents an experimental study on the axial compression performance of square duplex stainless steel tube ultra-high performance concrete (UHPC) short columns. The paper is published in Engineering Mechanics (2024, Vol. 41, No. 12, pp. 116–127) and is supported by the National Natural Science Foundation of China.

The authors designed and tested nine square duplex stainless steel tube UHPC short columns, three square duplex stainless steel tube ordinary concrete short columns, and three square duplex stainless steel tube specimens. The main test parameters were the width-to-thickness ratio of the duplex stainless steel tube and the core concrete strength.

Technical Interpretation

Experimental Program

The test matrix is well-designed to isolate the effects of the width-to-thickness ratio and the concrete strength. The inclusion of ordinary concrete specimens allows a direct comparison with UHPC specimens. The inclusion of empty steel tube specimens allows the contribution of the steel tube to be assessed.

The key test parameters are summarized below.

Parameter Description Practical Relevance
Width-to-thickness ratio Varies with wall thickness (4 mm to 8 mm) Governs local buckling and confinement
Concrete strength UHPC vs. ordinary concrete Affects failure mode and capacity
Steel tube type Duplex stainless steel Corrosion resistance and high strength
Number of specimens Nine UHPC, three ordinary, three empty Adequate for parametric study

Failure Modes and the Effect of Width-to-Thickness Ratio

The paper reports that the confinement coefficient is the main factor affecting the failure mode and the ultimate axial bearing capacity of the square duplex stainless steel tube UHPC short columns. As the stainless steel wall thickness increases from 4 mm to 8 mm, the failure mode changes from shear-type to "upsetting" type.

The key results are summarized below.

Parameter Change Effect
Wall thickness 4 mm to 8 mm Failure mode changes from shear to upsetting
Ultimate capacity Increase Average increase of 55.43%
Residual strength Increase Average increase of 17.45%
Confinement coefficient Main factor Governs failure mode and capacity

The Effect of Concrete Strength

The paper discusses the strength improvement index, the concrete contribution rate, and the ductility of the specimens. The UHPC provides a higher strength but a more brittle behavior. The confinement provided by the steel tube is essential to achieve a ductile failure.

The Effect of Chamfering

The paper also discusses the effect of chamfering on the stiffness of the short columns. Chamfering the corners of the square tube can improve the confinement and the stiffness. The paper proposes a relationship between the effective confined area and the width-to-thickness ratio.

Predictive Formula

Based on the test results and the Mander confined concrete model, the authors established a predictive formula for the ultimate bearing capacity of square duplex stainless steel tube UHPC short columns using the superposition principle. The formula is reported to have good accuracy.

Engineering Practice and Integration

What This Means for the Shop Floor and Site

As someone who has supplied stainless steel tubes for structural applications, I know that duplex stainless steel is more expensive than carbon steel but offers superior corrosion resistance and higher strength. The use of UHPC is a recent development that offers even higher strength but requires careful design.

Practical Lessons Learned

  1. The confinement coefficient is the key. The paper's finding that the confinement coefficient is the main factor affecting the failure mode and capacity is a critical design lesson. You cannot design a square stainless steel tube UHPC column without considering the confinement coefficient.
  2. Chamfering is beneficial. The paper's discussion of the effect of chamfering on the stiffness is a practical insight. Chamfering the corners of the square tube can improve the confinement and the stiffness.
  3. UHPC is not a drop-in replacement for ordinary concrete. UHPC has different mechanical properties, including a higher strength and a more brittle behavior. The design must account for these differences.

A Case from My Experience

I recall a project where stainless steel tubes were used for a marine structure. The use of duplex stainless steel was necessary for corrosion resistance. The design used ordinary concrete, but the paper suggests that UHPC could have been used to reduce the column size. However, the higher cost of UHPC and the need for careful quality control would need to be considered.

Key Questions and Reflections

  1. What is the optimal width-to-thickness ratio? The paper tests two ratios, but the optimal ratio depends on the concrete strength and the confinement coefficient.
  2. How does the chamfering affect the capacity? The paper discusses the effect of chamfering on the stiffness, but not on the capacity. This is a gap that needs to be addressed.
  3. What is the long-term behavior? The paper is limited to short-term loading. The long-term behavior, including creep and shrinkage, is not addressed.

Study Insights and Implications

This paper provides valuable experimental data on the behavior of square duplex stainless steel tube UHPC short columns under axial compression. The findings are directly applicable to design practice. The key insight is that the confinement coefficient is the main factor affecting the failure mode and capacity.

For the steel pipe manufacturer, the implications are clear: the width-to-thickness ratio must be controlled within tight tolerances. The use of duplex stainless steel requires careful handling and welding to avoid contamination and to maintain corrosion resistance.

Reference Value and Outlook

This paper is a useful reference for structural engineers designing square duplex stainless steel tube UHPC columns. The experimental data provides a basis for validating numerical models and for developing design equations. The future direction should be to extend the study to include a wider range of parameters, such as different steel grades, different concrete strengths, and different chamfering angles.

In conclusion, this paper presents a well-designed experimental study that provides valuable insights into the behavior of square duplex stainless steel tube UHPC short columns. The findings are practical and directly applicable to design. For the industry veteran, the lesson is that the confinement coefficient is the key parameter to consider when designing these columns, and the manufacturing process must be controlled to achieve the required width-to-thickness ratio.