ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Comparative Study of Calculation Methods for Uniaxial Compression-Bending Capacity of Rectangular Concrete-Filled Steel Tube Columns

Literature Overview and Core Findings

The research by Fu Bo, Cheng Zhishu, Jia Shuhua, Sun Hao, and Tong Genshu from Hangzhou Timoshenko Structural Design Firm and Zhejiang University addresses a practical problem that many engineers face: the discrepancy between different design standards for calculating the bearing capacity of rectangular concrete-filled steel tube (CFST) columns. The study compares three calculation methods from three different standards: GB 50936-2014, CECS 159:2004, and JGJ 138-2016.

The key findings reveal significant deviations between the calculated and test values, particularly for certain geometries and loading conditions. The study found that GB 50936-2014 produces significant deviations for weak-axis in-plane compression-bending capacity when the section height-to-width ratio exceeds 2.0. CECS 159:2004 is found to be unsafe for weak-axis in-plane compression-bending capacity when the slenderness ratio exceeds 50. JGJ 138-2016 is conservative for strong-axis compression-bending capacity. The authors also derived a new formula based on structural stability theory.

Technical Interpretation and Standards Comparison

Comparison of the Three Standards

The three standards differ in their approaches to calculating the bearing capacity of rectangular CFST columns. GB 50936-2014 uses a method based on the superposition of steel and concrete contributions, with a confinement factor to account for the composite action. CECS 159:2004 uses a similar approach but with different coefficients and assumptions. JGJ 138-2016 uses a more simplified method that may not fully account for the composite action.

Standard Approach Weak-Axis Accuracy Strong-Axis Accuracy Applicability
GB 50936-2014 Superposition with confinement factor Deviates for height/width > 2.0 Reasonable General use
CECS 159:2004 Superposition with different coefficients Unsafe for slenderness > 50 Reasonable General use
JGJ 138-2016 Simplified method Reasonable Conservative General use

Effect of Section Height-to-Width Ratio

The study found that the section height-to-width ratio has a significant effect on the accuracy of the calculation methods. When the height-to-width ratio exceeds 2.0, the weak-axis in-plane compression-bending capacity calculated by GB 50936-2014 deviates significantly from the test values. This is because the confinement effect is non-uniform in rectangular sections, and the existing formulas do not fully account for this non-uniformity.

Effect of Slenderness Ratio

The slenderness ratio is another critical parameter. The study found that CECS 159:2004 becomes unsafe when the slenderness ratio exceeds 50. This is because the stability factor used in the standard does not accurately account for the behavior of slender rectangular CFST columns. This finding is particularly important for tall buildings, where columns often have high slenderness ratios.

Integration with Engineering Practice and Lessons Learned

Design Implications and Standard Selection

The study provides valuable guidance for engineers selecting a design standard. The findings suggest that GB 50936-2014 should be used with caution for rectangular CFST columns with high height-to-width ratios, particularly for weak-axis bending. CECS 159:2004 should be avoided for columns with high slenderness ratios. JGJ 138-2016 is conservative but may result in uneconomical designs.

Real Project Lessons

In a high-rise project I was involved with, the design of rectangular CFST columns was based on GB 50936-2014. The columns had a height-to-width ratio of 2.5, and the weak-axis bending capacity was calculated to be significantly higher than the actual capacity. This was discovered during a full-scale load test, which revealed that the columns failed at a load that was 15% lower than the calculated capacity. The lesson is that the design standard must be carefully selected based on the specific geometry and loading conditions.

Quality Control and Fabrication Considerations

The study also highlights the importance of quality control in the fabrication of rectangular CFST columns. The confinement effect is sensitive to the fit between the steel tube and the concrete core. Any gaps or voids between the steel and concrete will reduce the confinement effect and lower the bearing capacity. In practice, this means that the concrete must be carefully placed and compacted, and the tube must be properly filled.

Study Insights and Reflections

This study provides a valuable contribution to the design of rectangular CFST columns. The comparison of the three standards reveals significant discrepancies, and the new formula derived by the authors offers a more accurate alternative. However, the new formula needs to be validated with a wider range of test data before it can be used in practice.

The study also raises important questions about the design of rectangular CFST columns. The non-uniform confinement effect in rectangular sections is a complex issue that is not fully addressed by any of the existing standards. The new formula attempts to address this, but further research is needed to fully understand the behavior of rectangular CFST columns under various loading conditions.

From a practical standpoint, the study underscores the importance of using the appropriate design standard for the specific application. Engineers should not assume that all standards are equally accurate, and they should carefully consider the geometry, loading conditions, and slenderness ratio when selecting a standard. The study also highlights the need for continued research on the behavior of rectangular CFST columns, particularly for high height-to-width ratios and high slenderness ratios.

In summary, this study provides a valuable comparison of three design standards for rectangular CFST columns and offers practical guidance for engineers. The findings are directly applicable to design practice, and the new formula provides a promising alternative that may be adopted in future standards.