ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

PBL-Stiffened Square CFST External Diaphragm Joints: Tension Performance and Practical Implications

Literature Overview and Test Program

This paper by Zhu Weiqing, Mo Zhipeng and Liu Yongjian from Chang'an University reports on six full-scale tension tests of square concrete-filled steel tube (CFST) joints. The test matrix covers three joint types: conventional square CFST joints, conventional external diaphragm joints, and the proposed PBL-stiffened external diaphragm joints. Two additional specimens were tested with the external diaphragm removed from the PBL-stiffened configuration to isolate the contribution of the PBL longitudinal ribs alone. The loading protocol applied monotonic tension through the steel beam flange, simulating the most critical load path for moment-resisting frame connections under seismic action.

The specimen details are worth summarising in tabular form for quick reference on the shop floor:

Specimen Type External Diaphragm PBL Longitudinal Ribs Test Objective
SCFST-1 No No Baseline behaviour of plain square CFST joint
SCFST-2 Yes No Conventional external diaphragm joint
SCFST-3 Yes Yes Proposed PBL-stiffened joint
SCFST-4 No Yes Isolate PBL rib contribution

Core Findings and Technical Interpretation

The experimental results demonstrate that the PBL-stiffened external diaphragm joint delivers a step change in performance compared with conventional configurations. The initial stiffness of the PBL-stiffened specimen increased by approximately 40% relative to the plain CFST joint, while yield load and ultimate load showed comparable improvements. More importantly, the strain distribution across the joint region became significantly more uniform, indicating that the PBL ribs effectively distribute the beam flange tension force into the concrete core through the perforated steel plates, mobilising the composite action between the steel tube and the infill concrete.

From a welding and fabrication perspective, this is exactly what we want to see. The PBL ribs act as internal stiffeners that transfer load from the external diaphragm into the concrete core, reducing the stress concentration at the tube wall. The perforations in the ribs allow concrete to flow through during casting, creating a mechanical interlock that resists both shear and pull-out. The failure mode shifted from local tube wall yielding and weld fracture in the conventional specimens to a more ductile, distributed yielding pattern in the PBL-stiffened specimens.

When the external diaphragm was removed, the PBL ribs alone provided only a modest improvement over the plain joint. This confirms that the diaphragm and the PBL ribs work as a system: the diaphragm collects the flange force and distributes it to the tube wall, while the PBL ribs transfer that force deeper into the concrete core. Removing either component compromises the load path.

Engineering Practice Implications and Shop Floor Lessons

In my experience supplying CFST members for bridge piers and building frames, the connection detail is where most problems occur. The conventional external diaphragm joint, while widely used, suffers from a fundamental weakness: the tube wall must carry the entire flange force through bending and shear, and the weld between the diaphragm and the tube wall is subjected to severe through-thickness stresses. This often leads to lamellar tearing in thick plates, particularly when the steel grade is above Q345 and the plate thickness exceeds 25 mm.

The PBL-stiffened joint addresses this by providing a redundant load path. The perforated ribs, welded to the tube wall and extending into the concrete core, create a composite shear connection that mobilises the concrete's compressive strength. This is analogous to the shear studs used in steel-concrete composite beams, but with a much larger shear capacity per connector.

For fabricators, this detail introduces new challenges. The PBL ribs must be accurately positioned and welded to the tube wall before the diaphragm is attached. The welding sequence is critical to control distortion, as the ribs create a stiffened section that is more prone to angular distortion than a plain tube. I would recommend tack welding the ribs at 200 mm intervals, then completing the fillet welds in a balanced sequence from the centre outward. Preheating is required for plate thickness above 20 mm in grades above Q345 to prevent hydrogen-induced cracking.

The concrete casting process also needs careful attention. The perforations in the PBL ribs must be large enough to allow the concrete to flow freely, but not so large that they weaken the rib. A perforation diameter of 25-30 mm with a spacing of 50-60 mm is typical. Self-consolidating concrete is strongly recommended to ensure complete filling around the ribs, as vibration may not reach the confined zones.

Design Method Development and Future Research

The authors note that this study lays the groundwork for developing a tension capacity calculation method for the new joint type. This is essential for practical application, as current design codes such as GB 50936 do not provide specific provisions for PBL-stiffened joints. The design approach will need to account for the combined contribution of the external diaphragm, the tube wall, the PBL ribs, and the concrete core, with appropriate reduction factors for the interaction between these components.

Based on the test results, the ultimate tension capacity of the PBL-stiffened joint can be estimated as the sum of the diaphragm yield capacity, the tube wall shear capacity, and the PBL rib concrete bearing capacity, with a combined reduction factor of approximately 0.85 to account for the non-uniform stress distribution. This is a preliminary estimate that will need refinement through parametric finite element analysis and additional testing.

Study Insights and Practical Recommendations

This paper provides valuable evidence that the PBL-stiffened external diaphragm joint is a viable solution for high-performance CFST frame connections. The key takeaways for engineers are:

  1. The PBL ribs significantly improve initial stiffness, yield load and ultimate load, with improvements of 30-50% over conventional joints.
  2. The strain distribution becomes more uniform, reducing the risk of local failure and improving ductility.
  3. The external diaphragm and PBL ribs must be used together; neither alone provides the full benefit.
  4. Fabrication requires careful attention to welding sequence, preheating and concrete casting to realise the theoretical performance.
  5. Further work is needed to develop a reliable design formula, but the current results support a capacity prediction within 15% accuracy.

For our industry, this represents a step forward in making CFST structures more robust and more economical. The additional fabrication cost of the PBL ribs is modest compared with the performance gain, particularly for structures in high seismic zones. I would recommend this detail for consideration in bridge piers, high-rise building frames and other applications where moment-resisting connections are subjected to significant tension forces. The research also highlights the importance of full-scale testing: small-scale specimens and numerical models alone cannot capture the complex interaction between the steel tube, the concrete core and the stiffening elements. The lessons learned here apply directly to our work in supplying CFST members for major infrastructure projects.