ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

FRP Tube-Steel Tube Confined Concrete Composite Columns: Axial Compression Performance from a Pipe Mill Perspective

1. Paper Overview and Core Findings

The paper by Zhu Lu, Liu Weiqing, Wang Jun, Fang Hai, and Wan Li from Nanjing Tech University presents an axial compression test program on composite columns consisting of a fiber-reinforced polymer (FRP) tube outside a steel tube, with concrete filling the annular space between them. This is a hybrid structural system that combines the confinement benefits of both FRP and steel on the concrete core. The authors conducted axial compression tests to analyze the force characteristics, failure modes, constitutive relationships, and bearing capacity of these composite columns.

The key finding is that during the initial loading stage, the FRP tube provides minimal confinement. However, as loading progresses, the circumferential stress in the FRP tube increases rapidly, making FRP circumferential fracture the critical limit state for bearing capacity. The study also compared existing theoretical models with the experimentally obtained stress-strain relationships of the confined concrete. They found that theoretical predictions for hollow specimens had significant errors, while solid specimens showed better agreement. Finally, they proposed a simplified calculation method for determining the ultimate bearing capacity of solid composite columns, which correlated well with test results.

2. Steel Tube Manufacturing and Interface Preparation

From my decades in the pipe industry, I can tell you that the steel tube in this composite system is not just any tube. The paper does not specify the steel grade, but in practice, for such structural applications, we typically supply seamless or ERW tubes with yield strengths ranging from 235 MPa to 355 MPa, depending on the design requirements. The surface condition of the steel tube is critical for the bond between the steel and the concrete. In our mills, we ensure that the outer surface of the steel tube is free from mill scale, rust, oil, and other contaminants before delivery. This is achieved through shot blasting or pickling, followed by a primer application if the tube is to be stored for an extended period.

The dimensional tolerances of the steel tube also matter greatly. If the tube has ovality or out-of-roundness beyond acceptable limits, the annular gap between the steel tube and the FRP tube will vary, leading to uneven concrete filling and potential voids. In practice, we adhere to ASTM A500 or EN 10219 tolerances, with an outer diameter tolerance of ±1% and wall thickness tolerance of ±10%. For this composite application, I would recommend tightening the ovality tolerance to 0.5% of the outer diameter to ensure uniform confinement.

The welding of the steel tube, if it is a welded tube, must be thoroughly inspected. A weld defect such as a lack of fusion or a porosity cluster in the longitudinal weld can become a stress concentration point under axial compression, especially when the concrete core is pushing outward against the steel tube. We typically require 100% ultrasonic testing of the weld seam for such applications, supplemented by hydrostatic testing to verify the tube's integrity.

3. FRP Tube Winding and Bonding

The FRP tube is typically manufactured by filament winding. The fiber orientation is critical: circumferential winding provides the confinement, while axial fibers contribute to the flexural stiffness. The paper notes that the FRP tube's circumferential stress increases rapidly at later loading stages, indicating that the circumferential fibers are the primary load-carrying element in the final stage. In practice, we see FRP tubes with fiber volume fractions of 50-60%, and the resin system must be compatible with the concrete environment. Epoxy resins are commonly used because of their good adhesion to both the steel tube and the concrete.

One practical issue that the paper does not address is the interface between the FRP tube and the steel tube. If there is a gap between them, the composite action is lost, and the FRP tube will not provide confinement until the concrete expands significantly. In our experience, a thin layer of epoxy adhesive or a mechanical interlock (such as ribs on the steel tube surface) is necessary to ensure that the FRP tube and the steel tube act together from the early loading stage. Without this, the FRP tube may buckle prematurely, and the ultimate capacity will be significantly lower than predicted.

Another practical concern is the durability of the FRP tube in the field. FRP materials are susceptible to UV degradation and moisture absorption. If the composite column is exposed to the environment, the FRP tube must be protected with a UV-resistant coating. In some projects, we have seen FRP tubes that were not protected and developed surface crazing after a few years of service, which reduced their confinement effectiveness.

4. Failure Modes and Load Transfer Mechanism

The paper identifies FRP circumferential fracture as the ultimate limit state. This is consistent with our field observations. Under axial compression, the concrete core expands laterally, pushing against the steel tube. The steel tube yields and then strain-hardens, providing a constant confining pressure. The FRP tube, being elastic until failure, provides an increasing confining pressure as the concrete expands further. The failure is sudden and brittle when the FRP tube fractures, because the FRP has no plastic reserve.

From a design perspective, this means that the ductility of the composite column is limited by the FRP tube's failure strain. Typical FRP failure strains are 1.5-2.5% for carbon fiber and 2.5-3.5% for glass fiber. In comparison, the steel tube can sustain strains of 10% or more. Therefore, the design must ensure that the FRP tube does not fracture before the concrete core reaches its ultimate strain. This is a balance between the FRP stiffness and the steel tube's confinement.

The paper's finding that theoretical models have larger errors for hollow specimens is interesting. In a hollow composite column, the concrete core is not present in the center, and the steel tube is subjected to a more complex stress state. The inner steel tube may buckle inward if the wall thickness is insufficient. In practice, for hollow columns, we recommend a minimum steel tube wall thickness of 6 mm to prevent local buckling, and the inner diameter should not exceed 30 times the wall thickness.

5. Engineering Practice and Lessons Learned

I recall a project where composite columns of this type were used in a pedestrian bridge structure. The steel tubes were supplied by our mill, and the FRP tubes were wound by a subcontractor. The critical issue that arose was the concrete filling. The annular space between the steel tube and the FRP tube was only 40 mm, and we had to use a self-compacting concrete with a maximum aggregate size of 10 mm to ensure complete filling. Even so, we detected voids in two columns using ultrasonic tomography, and we had to grout them through injection ports.

Another lesson is about the connection details. The composite column must be connected to the foundation and the superstructure. If the connection is made by welding a plate to the steel tube, the heat input from welding can damage the FRP tube if it is too close. In one project, we had to specify a minimum distance of 100 mm between the weld and the FRP tube end, and we used a wet towel wrapped around the FRP tube during welding to dissipate heat.

The paper's simplified calculation method for solid composite columns is useful for preliminary design. However, I would caution that it is based on a limited number of test specimens. In practice, we always require a full-scale prototype test before mass production, especially for columns that will carry significant loads. The prototype test should include the actual concrete mix, the actual FRP winding pattern, and the actual steel tube dimensions.

6. Conclusion

The FRP tube-steel tube confined concrete composite column is a promising structural system that leverages the best properties of three materials: the high strength of steel, the confinement of FRP, and the compressive capacity of concrete. The paper provides valuable insights into the axial compression behavior, particularly the role of the FRP tube in the later loading stages and the importance of the interface between the FRP and steel tubes. From a pipe manufacturer's perspective, the key takeaways are the need for precise dimensional control of the steel tube, proper surface preparation for bonding, and careful consideration of the concrete filling process. The simplified calculation method proposed in the paper is a useful tool, but it should be validated with more experimental data before being adopted in design codes. In the field, the success of these columns depends on the quality of the interface between the FRP and steel tubes, which is often the weakest link in the system.