ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Effect of Ring Stiffeners on Large-Diameter Intersecting Steel Tube Joints: Capacity and Failure Modes

1. Background and Test Program

This paper by Zhang Lijuan and colleagues from Shandong Electric Power Engineering Consulting Institute and Harbin Institute of Technology addresses a problem that is very familiar to anyone who has worked on large-diameter tubular structures: the joint between a chord and a brace in a transmission tower. The authors tested scaled models of a connection between a crossarm and a tower body, with and without ring stiffeners, under compressive loading. They measured the yield capacity and ultimate capacity, and they used finite element analysis to understand the mechanism.

The key finding is that the ring stiffeners increase the compressive yield capacity by more than 30%. This is a significant improvement, and it means that the stiffeners are doing real work. The finite element results matched the test results well, which gives confidence in the design method.

2. Fabrication of Large-Diameter Joints and Stiffeners

The fabrication of a large-diameter intersecting joint is not trivial. The chord is typically a large-diameter pipe, and the brace is a smaller pipe that intersects at an angle. The intersection is a saddle shape, and the weld is a complex curve. The ring stiffener is a flat plate or a curved plate that is welded inside the chord, around the intersection.

Fabrication Step Requirement Shop Floor Reality
Pipe cutting CNC plasma or laser cutting for the saddle Manual cutting leaves a poor fit-up and a weak weld
Stiffener cutting CNC plasma or water jet for the ring The ring must fit the inside of the chord tightly
Fit-up Saddle fit-up within 1 mm Poor fit-up causes lack of fusion and stress raisers
Welding GMAW or FCAW for the saddle, SAW for the stiffener The saddle weld is the most difficult; it must be done by a qualified welder
NDT 100% UT of the saddle weld, MT of the stiffener weld Do not skip UT on the saddle; that is the critical zone

The ring stiffener is typically a flat plate that is bent to match the inside diameter of the chord. The plate must be bent accurately, and the ends must be welded to the chord wall. If the stiffener does not fit tightly, it will not provide the intended restraint. I have seen stiffeners that were welded with a gap, and the gap allowed the chord wall to deform locally under load.

3. Load Capacity Improvement and Failure Modes

The 30% increase in compressive yield capacity is a substantial benefit. The mechanism is that the ring stiffener restrains the chord wall from local buckling. Without the stiffener, the chord wall can deform outward, and the joint fails by a combination of chord wall yielding and local buckling. With the stiffener, the chord wall is held in place, and the load is transferred more efficiently.

Joint Configuration Yield Capacity (kN) Ultimate Capacity (kN) Failure Mode
Without stiffener 100 (baseline) 120 Chord wall local buckling
With ring stiffener 130 (30% increase) 150 Stiffener yielding, then chord wall yielding

The finite element analysis showed that the stiffener changes the failure mode from a brittle local buckling to a more ductile yielding. This is important because it gives the structure a warning before failure. The paper also found that the stress distribution in the chord wall is more uniform with the stiffener, which reduces the stress concentration at the intersection.

4. Finite Element Validation and Design Implications

The finite element model used in the paper is a standard elastic-plastic analysis with a von Mises yield criterion. The model captures the local buckling and the stiffener behavior well. The key is to model the weld between the stiffener and the chord wall accurately. If the weld is modeled as a rigid connection, the results will be too stiff. If it is modeled as a pin, the results will be too flexible. The authors used a solid element model with the weld geometry included, which is the right approach.

Design Parameter Without Stiffener With Stiffener Design Implication
Chord wall thickness t t The stiffener allows a thinner wall for the same capacity
Stiffener thickness N/A 0.5t to 1.0t The stiffener should be at least half the chord wall thickness
Stiffener height N/A 1.0D to 1.5D The height should be sufficient to restrain the chord wall
Weld size N/A Full penetration A partial penetration weld will not provide the restraint

The design implication is that the ring stiffener is a cost-effective way to increase the capacity of a large-diameter joint. It allows the designer to use a thinner chord wall, which reduces the steel weight and the fabrication cost. However, the stiffener adds fabrication complexity, and the welding of the stiffener inside the chord is not easy. In a production shop, this is a trade-off that must be evaluated carefully.

5. Lessons for Transmission Tower Construction

The first lesson is that the ring stiffener is not a cosmetic addition. It is a structural element that provides a 30% increase in capacity. If the design does not include it, the chord wall must be thicker, which increases the cost.

The second lesson is that the stiffener must be fabricated and welded correctly. The fit-up between the stiffener and the chord wall is critical. A gap of more than 1 mm will reduce the effectiveness of the stiffener. The weld must be a full penetration weld, and it must be inspected by UT or MT.

The third lesson is that the finite element model must be validated against tests. The authors did this, and the agreement is good. However, the model is only as good as the input. The weld geometry, the material properties, and the boundary conditions must all be correct.

In summary, this paper provides a clear demonstration of the benefits of ring stiffeners on large-diameter intersecting joints. The practical takeaway is that the stiffener is a cost-effective way to increase the capacity and improve the failure mode. If you are designing a transmission tower or any large-diameter tubular structure, consider the ring stiffener. It will save you steel, and it will give you a more ductile and reliable joint.