ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Calculation Method for Eccentric Compression Bearing Capacity of Rectangular Concrete-Filled Steel Tube Based on Wall Plate Post-Buckling Strength: A Veteran's Reading of Wang Haitao et al. (2022)

Literature Overview and Context

This paper by Wang Haitao, Liu Yongjian and Sun Lipeng, published in the Journal of Architecture and Civil Engineering in 2022, proposes a calculation method for the eccentric compression bearing capacity of rectangular concrete-filled steel tube (CFST) columns with large width-to-thickness ratios. The authors first studied the buckling behaviour of non-uniformly compressed one-sided restrained plates using finite element analysis, and derived a formula for the elastic buckling coefficient of such plates. They then combined this with the effective width method to propose two calculation methods for the eccentric compression bearing capacity of rectangular CFST columns based on the post-buckling strength of the wall plates. The work is supported by the National Natural Science Foundation of China (51778058).

This paper is directly relevant to us in the pipe and fitting industry because rectangular CFST columns with large width-to-thickness ratios are becoming more common in modern construction. The large width-to-thickness ratio means that the wall plates are slender and prone to buckling. The post-buckling strength of the wall plates is an important factor in the bearing capacity of the column.

Core Findings and Technical Interpretation

The authors proposed two calculation methods. Method 1 is based on the effective width method, which reduces the width of the plate to account for the buckling. Method 2 is a refinement that provides a more accurate assessment of the bearing capacity.

Parameter Finding Practical Implication
Elastic buckling coefficient Formula derived for non-uniformly compressed one-sided restrained plates The coefficient depends on the stress gradient and the restraint conditions
Effective width method Method 1 provides good accuracy The effective width accounts for the post-buckling strength
Refined method Method 2 provides better accuracy The refined method accounts for the interaction between the wall plates and the concrete core
Comparison with standards Both methods are more accurate than the current code methods The current codes underestimate the bearing capacity of large width-to-thickness ratio columns

The key finding is that the current code methods underestimate the bearing capacity of large width-to-thickness ratio rectangular CFST columns. The proposed methods provide a more accurate assessment, and Method 2 is the most accurate.

The elastic buckling coefficient formula is the theoretical foundation. The coefficient depends on the stress gradient, which is determined by the eccentricity of the load. For a column under eccentric compression, the stress distribution across the section is non-uniform, and the wall plate on the compression side is subjected to a higher stress than the wall plate on the tension side. The buckling coefficient accounts for this non-uniformity.

Manufacturing and Delivery Practice: What This Means for Us

From the shop floor perspective, rectangular CFST columns with large width-to-thickness ratios are a fabrication challenge. The wall plates are slender, and they are prone to buckling during handling and welding. The fabricator must ensure that the wall plates are properly supported during welding to prevent distortion.

The most common problem I have seen with rectangular CFST columns is that the wall plates are not flat. The flatness tolerance is critical because the concrete core provides lateral support to the wall plates. If the wall plates are not flat, the concrete may not fill the gap, and the lateral support is reduced. The result is that the wall plates buckle prematurely, and the bearing capacity is reduced.

Another common problem is that the corner welds are not properly executed. The corner welds connect the wall plates, and they must be full penetration to ensure that the section behaves as a single unit. If the corner welds are not full penetration, the section may separate at the corners, and the wall plates may buckle independently.

In my experience, the most important thing is to control the width-to-thickness ratio. If the width-to-thickness ratio is too large, the wall plates are too slender, and the post-buckling strength is low. The design must limit the width-to-thickness ratio to ensure that the post-buckling strength is adequate. The paper provides a method for calculating the bearing capacity, but the fabricator must ensure that the width-to-thickness ratio is within the design limits.

Standards and Specification Gaps

The paper compares the proposed methods with the current code methods. The current codes underestimate the bearing capacity of large width-to-thickness ratio columns. This is a significant finding because it means that the current codes are conservative for this type of column. The proposed methods provide a more accurate assessment, which could lead to more economical designs.

In practice, this means that the project specification must define the calculation method to be used. If the current code method is used, the design is conservative, and the column may be over-designed. If the proposed method is used, the design is more accurate, and the column may be more economical. The specification must clearly state which method is to be used, and the designer must provide the necessary calculations.

Study Insights and Reflections

What I take from this paper is that the post-buckling strength of the wall plates is an important factor in the bearing capacity of rectangular CFST columns. The current codes do not fully account for this, and the proposed methods provide a more accurate assessment.

The other lesson is that the width-to-thickness ratio is a critical design parameter. If the ratio is too large, the wall plates are too slender, and the post-buckling strength is low. The design must limit the width-to-thickness ratio to ensure that the post-buckling strength is adequate. The paper provides a method for calculating the bearing capacity, but the fabricator must ensure that the width-to-thickness ratio is within the design limits.

Reference Value and Outlook

This paper is a valuable contribution to the literature on the bearing capacity of rectangular CFST columns. The derivation of the elastic buckling coefficient formula is clear, and the comparison with the current code methods is useful. The practical value to us in the pipe and fitting industry is the emphasis on the width-to-thickness ratio and the post-buckling strength of the wall plates. If we are asked to supply rectangular CFST columns with large width-to-thickness ratios, we should ask the designer about the calculation method and the expected bearing capacity. The paper gives us a good starting point for that conversation.