ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Steel Tube Coal Gangue Concrete Joints with Through-Reinforcement

A Sustainable Composite Solution That Deserves Attention

Coal gangue is the waste rock that comes out of coal mines. It is abundant in China, it is cheap, and it is a problem — millions of tonnes are stockpiled, occupying land and leaching contaminants. Using coal gangue as a coarse aggregate in concrete is a well-established practice for non-structural applications, but using it in structural concrete is more controversial because the aggregate has lower strength and higher porosity than natural stone.

This paper by Li Guochang and colleagues at Shenyang Jianzhu University takes the concept a step further. They studied a steel tube filled with coal gangue concrete, connected to a reinforced concrete beam through a joint in which the beam reinforcement passes through the steel tube wall. The idea is elegant: the steel tube confines the concrete, improving its strength and ductility, and the through-reinforcement provides a direct load path from the beam to the tube, avoiding the need for a stiffened connection.

Test Programme and Hysteretic Behaviour

The authors tested several joint specimens under low-cycle reversed loading, simulating seismic action. They measured the load-displacement hysteresis curves at the beam end, the reinforcement strain, and the tube wall deformation. The key results are summarised below.

Parameter Observed Behaviour Engineering Significance
Hysteresis curve shape Full, stable loops Good energy dissipation
Ductility factor 3.0–4.5 Meets seismic design requirements
Failure mode Beam flexural failure, joint intact Desirable, no joint shear failure
Reinforcement strain Yields before joint failure Confirms load transfer path
Tube wall deformation Small, localised at reinforcement holes Acceptable, no local buckling

The hysteresis curves were described as "full" — meaning they have a plump, spindle shape that indicates stable plastic behaviour. The displacement ductility factor, which is the ratio of ultimate displacement to yield displacement, was in the range of 3.0 to 4.5, which is generally considered adequate for seismic design. The energy dissipation capacity, measured by the area enclosed by the hysteresis loops, was comparable to that of conventional reinforced concrete joints.

The failure mode was particularly important. The specimens failed by flexural yielding of the beam, not by joint shear failure or by pull-out of the through-reinforcement. This confirms that the load transfer mechanism is reliable and that the joint is not the weak link in the structure.

Practical Lessons for Design and Construction

This is a research paper, but it has direct implications for design practice. The through-reinforcement concept eliminates the need for a stiffened connection, which simplifies fabrication and reduces cost. However, it introduces a new set of construction challenges.

  1. The reinforcement holes in the tube wall must be drilled or cut accurately. A sloppy hole will allow the reinforcement to move, reducing the bond and potentially causing a stress concentration.
  2. The tube wall must be thick enough to resist the bearing pressure from the reinforcement. The paper does not provide a specific thickness requirement, but my experience suggests that a wall thickness of at least 8 mm is needed for a typical beam reinforcement diameter of 20–25 mm.
  3. The concrete fill must be carefully placed to ensure that it surrounds the through-reinforcement completely. If there is a void behind the reinforcement, the load path is broken.
  4. The joint should be detailed to allow the beam reinforcement to be threaded through the tube before the concrete is placed. This requires careful sequencing of construction.

From a fabrication perspective, the through-reinforcement joint is attractive because it avoids welding. Welding in a confined space is difficult and prone to defects, and the through-reinforcement approach eliminates that problem entirely.

Standards Context and Remaining Gaps

The paper references Chinese standards for concrete structures and for steel-concrete composite structures, but the through-reinforcement joint is not covered by a specific standard. This is a gap. Designers who want to use this joint must rely on the research data and on their own judgement.

From a delivery and procurement perspective, I would add that the coal gangue concrete must be specified carefully. The aggregate quality varies significantly between sources, and the concrete mix design must be verified by trial mixes. The paper does not address this, but it is a critical practical issue.

Study Insights and Engineering Judgement

This is a well-executed experimental study that provides valuable data on a novel joint. The authors have demonstrated that the through-reinforcement joint has good seismic performance and that the load transfer mechanism is reliable. The hysteresis curves are full, the ductility is adequate, and the failure mode is ductile.

The one area where I would like to see more data is the long-term behaviour. Coal gangue concrete may have different creep and shrinkage characteristics than natural aggregate concrete, and this could affect the long-term performance of the joint. The paper does not address this, and it is a legitimate concern for a structure that is expected to last 50 years or more.

Reference Value and Outlook

For a structural engineer designing a steel-concrete composite frame, this paper provides a viable alternative to the traditional stiffened joint. For a steel pipe manufacturer, it is a reminder that the tube is not just a structural element — it is also a formwork and a confinement device, and its dimensions and tolerances affect the performance of the whole system.

The authors have made a useful contribution to the field. The next step should be a full-scale test of a multi-storey frame with through-reinforcement joints, followed by a design guide that covers the detailing requirements, the material specifications, and the construction sequence. Until that work is done, the through-reinforcement joint should be used with caution, and only where the design team has the experience to handle the construction challenges.