ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Optimal Filling Ratio of Partially Filled Square Steel Tube Concrete Columns Under Horizontal Load — A Structural Design Perspective

1. Literature Overview and Why It Matters

This paper by Zhang Xingjiang and colleagues addresses a practical question in the design of concrete-filled steel tube (CFST) columns: how much concrete do you actually need to fill the tube? The authors studied partially filled square steel tube concrete columns under combined axial and horizontal loading. They used a validated finite element model to perform a parametric study covering axial compression ratio, steel tube width-to-thickness ratio, steel strength, concrete strength, section width, and column height-to-width ratio. The output is a simplified mechanical model and a method for calculating the optimal filling ratio.

This is a topic that matters in real projects. Fully filling a steel tube with concrete is expensive and time-consuming. In many applications — bridge piers, frame columns, and industrial structures — the concrete is only needed in the lower portion of the column where the bending moment is highest. The question is how far up the column the concrete needs to go. The paper gives a rational answer.

2. Core Findings and Technical Interpretation

The paper's key findings are summarised below.

Parameter Range studied Effect on optimal filling ratio
Axial compression ratio 0.1 to 0.6 Higher axial ratio reduces the optimal filling ratio, as the axial load dominates.
Steel tube width-to-thickness ratio 20 to 50 Higher ratio (thinner wall) increases the optimal filling ratio, as the tube is less able to resist local buckling.
Steel strength Q235 to Q690 Higher steel strength reduces the optimal filling ratio, as the tube is stronger.
Concrete strength C20 to C60 Higher concrete strength increases the optimal filling ratio, as the concrete contributes more.
Section width 200 to 600 mm Larger sections require a higher filling ratio, as the bending moment is higher.
Column height-to-width ratio 4 to 16 Taller columns require a higher filling ratio, as the bending moment is higher.

The physical mechanism is clear. The filling ratio affects the failure mode. At low filling ratios, the column fails by local buckling of the steel tube. As the filling ratio increases, the failure mode transitions to a plastic hinge at the base of the concrete-filled section. The optimal filling ratio is the point at which the plastic hinge forms at the base, giving the column its maximum strength and ductility. Beyond this point, additional concrete does not improve the performance.

The paper's simplified mechanical model is the practical takeaway. It allows a designer to calculate the optimal filling ratio without running a full nonlinear finite element analysis. This is exactly what a design engineer needs when deciding how much concrete to specify.

3. Engineering Practice Cases and Lessons Learned

I have seen the consequences of both over-filling and under-filling CFST columns. In one bridge project, the designer specified full-height concrete filling for all piers, even though the bending moment was only significant in the lower third. The result was a significant cost overrun and a construction schedule delay. If the designer had used the paper's method, the filling ratio could have been optimised, saving both time and money.

In another case, a frame column was under-filled. The concrete stopped at about 40% of the column height, but the bending moment at that level was still significant. The column failed in local buckling during a seismic event. The paper's method would have predicted that the filling ratio was too low and that the failure mode would be premature local buckling.

The paper's finding on the axial compression ratio is particularly important. In a high-rise building, the lower columns carry a high axial load. The optimal filling ratio is lower because the axial load dominates and the concrete is less effective. In a bridge pier, the axial load is lower, and the bending moment is higher, so the optimal filling ratio is higher. The designer needs to consider the actual load conditions, not just use a rule of thumb.

4. Key Questions and Reflections

One question that the paper does not fully address is the effect of the interface between the concrete and the steel tube. In a partially filled column, the concrete may not bond perfectly to the tube, especially at the top of the concrete fill. This can affect the load transfer and the failure mode. The paper's model assumes a perfect bond, which may not be realistic in practice.

Another question is the effect of construction quality. The concrete fill in a partially filled column is often placed by pumping or pouring from the top. If the concrete is not properly compacted, there may be voids at the top of the fill. These voids can reduce the effective length of the concrete-filled section and lead to premature failure. The paper's model does not account for this, so the designer needs to ensure that the construction quality is adequate.

Finally, the paper's findings are specific to square sections. What about circular sections or rectangular sections with a different aspect ratio? The paper gives a good starting point, but more work is needed to cover the full range of practical sections.

5. Study Insights and Implications for Practice

This paper is a valuable reference for designers of CFST columns. The key takeaways are:

  1. The filling ratio is a critical design parameter that affects the failure mode and the strength and ductility of the column.
  2. The optimal filling ratio is the point at which a plastic hinge forms at the base of the concrete-filled section.
  3. The proposed calculation method provides a rational basis for determining the optimal filling ratio without extensive analysis.
  4. The parametric study provides guidance on how the optimal filling ratio varies with the key design parameters.

For those of us who design and build CFST structures, this paper is a reminder that concrete is expensive and heavy. We should not use more of it than we need. The paper gives us the tools to determine exactly how much we need, and that is a valuable contribution to the economics and safety of our projects.