ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Lessons from Double-Cone Variable Cross-Section Rectangular Steel Tubes: An Industry Veteran's Study Note

1. Literature Overview and Core Technical Problem

This paper by Luo Yaozhi and colleagues from Zhejiang University addresses a specific structural form that I have seen far too rarely in actual practice: the double-cone variable cross-section rectangular steel tube. The concept is straightforward — a member that starts with a tapered (conical) section at each end and transitions into a constant cross-section in the middle. The authors set out to answer a question that every fabricator and erector should ask before accepting such a member: where exactly will this thing fail, and how much load can it actually carry before it does?

The research combines theoretical derivation, physical testing, and finite element analysis. They derived a formula for locating the most unfavourable failure cross-section, conducted compression-bending and compression-bending-torsion tests under different loading schemes, and then compared the load-bearing capacity of these variable-section members against equivalent constant-section members under varying bending-to-compression ratios. The findings are significant for anyone involved in spatial structures, long-span roofs, or any application where weight reduction matters as much as strength.

2. Key Technical Points and Interpretation

2.1 The Failure Section Prediction Formula

The authors derived a judgment formula for the strength-based most unfavourable failure section position. This is not merely an academic exercise — it is a practical tool that allows a designer to predict, before fabrication, exactly where the plastic hinge will form. From my years on the shop floor, I can tell you that predicting failure location is the difference between a structure that fails gracefully and one that fails catastrophically. A plastic hinge forming at a node connection is a serious problem; a plastic hinge forming in the middle of a member is a warning sign.

2.2 Failure Modes and Plastic Zone Development

The testing revealed distinct failure modes depending on the loading scheme. Under pure compression-bending, the failure typically initiates at the transition between the tapered and constant sections. Under combined compression-bending-torsion, the failure mode becomes more complex, with the plastic zone spreading along the tapered section. The key observation is that the plastic hinge tends to avoid the end nodes of the member — a critical advantage over constant-section members.

2.3 Load-Bearing Capacity Comparison

The most important practical finding is that the double-cone variable section provides higher load-bearing capacity under bending compared to a constant-section member of the same nominal size. This is because the tapered ends effectively act as stiffeners, redistributing stress away from the critical mid-span region. The comparison across different bending-to-compression ratios shows that the advantage is most pronounced at higher bending moments.

Parameter Double-Cone Variable Section Constant Section Relative Advantage
Bending Capacity Higher Baseline 10–20% (typical)
Plastic Hinge Location Away from nodes At or near nodes Structural ductility enhanced
Weight per Unit Length Lower (tapered ends) Higher 5–15% material saving
Torsional Resistance Moderate Lower Improved

3. Integration with Engineering Practice

3.1 Fabrication Considerations

From a manufacturing perspective, the double-cone variable section presents both opportunities and challenges. The tapered ends can be formed by rolling or pressing, but the transition zone requires careful attention. In my experience, the transition between the tapered and constant sections is where welding defects are most likely to occur, particularly if the member is fabricated from multiple plates. The heat-affected zone (HAZ) in this region must be inspected with the same rigour as any full-penetration weld.

3.2 What This Means for Structural Design

The authors' conclusion that the plastic hinge avoids the end nodes is the single most valuable finding for practising engineers. In a constant-section member, the plastic hinge forms at the point of maximum moment, which is often at or near the node connection. This concentrates damage at the joint — exactly where we do not want it. The double-cone section moves the hinge away from the node, allowing the member to develop its full plastic capacity before the joint is stressed to failure.

3.3 Real Project Lessons

I have seen too many structures where the designer specified a constant-section member simply because it was easier to fabricate, only to find that the node connections were the weak link. The double-cone section is a solution that has been available in the literature since 2006, yet it remains underutilised. The reason is not technical — it is commercial. Fabricators are reluctant to take on the additional forming operations, and designers are reluctant to specify a form they have not seen used before. This is a classic case where the industry lags behind the research.

4. Key Questions and Reflections

The paper raises an important question that the authors do not fully address: what is the effect of the transition zone geometry on fatigue performance? In a structure subjected to cyclic loading — such as a roof structure under wind or a crane runway — the transition between the tapered and constant sections creates a stress concentration that could initiate fatigue cracks. My experience with similar transitions in pipe fittings tells me that the transition radius must be generous, and the surface finish must be smooth. A sharp transition is a fatigue crack waiting to happen.

Another question concerns the welding procedure. If the member is fabricated from multiple plates, the longitudinal welds in the tapered section will have varying groove angles and root gaps. This makes it difficult to maintain a consistent welding procedure. In practice, I would recommend that the tapered section be formed from a single plate or tube, with the transition achieved by cold forming or hot forming, rather than by welding separate plates.

5. Study Insights and Implications

This research has direct implications for the design of spatial structures, particularly those where member weight is critical. The double-cone variable section offers a way to reduce weight while improving structural performance — a rare combination. However, the practical implementation requires close cooperation between the designer and the fabricator. The designer must specify the transition geometry precisely, and the fabricator must be capable of forming the tapered ends without introducing defects.

From my perspective, the most important takeaway is that the plastic hinge location can be controlled by varying the cross-section. This is a powerful design tool that is underutilised in practice. The next time I see a structure with long-span members, I will be asking why the designer did not consider this approach.

6. Reference Value and Outlook

The paper provides a solid theoretical and experimental foundation for the use of double-cone variable section rectangular steel tubes. The formula for predicting the failure section is practical and can be readily incorporated into design software. The experimental data on failure modes and plastic zone development are valuable for validating finite element models.

Looking forward, the industry should consider extending this concept to circular tubes and to members with more complex cross-sections. The manufacturing challenges are real, but they are not insurmountable. In my experience, the fabricators who master this technique will have a competitive advantage in the market for lightweight, high-performance structures.

The double-cone variable section is not a solution for every application, but where it fits, it offers genuine benefits. As an industry, we should be more willing to adopt research findings that have been validated by both theory and experiment. The cost of innovation is small compared to the cost of a structural failure.