ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Seismic Response Analysis of a Half-Through CFST Arch Bridge

Overview of the Seismic Analysis

This paper presents a seismic analysis of a half-through concrete-filled steel tube (CFST) arch bridge. The arch ribs were modeled using the "unified theory," which converts the CFST section into an equivalent homogeneous material. The analysis included a modal analysis to determine the natural frequencies and mode shapes, followed by a time-history analysis using Rayleigh damping under both the basic and rare earthquake levels. The results showed that the bridge has a relatively low out-of-plane stiffness, and the seismic response is dominated by out-of-plane vibration and deformation. The paper also concluded that the CFST structure has excellent seismic performance and maintains sufficient ductility even under a rare earthquake.

For a pipe manufacturer, the arch ribs of a CFST bridge are a major fabrication challenge. The arch ribs are typically made from large-diameter, thick-walled pipe that is bent to the arch profile. The bending of the pipe introduces residual stresses and changes the mechanical properties of the steel. The welding of the arch segments is also critical, as the arch is a continuous structure that is subjected to high bending moments and axial forces.

Technical Interpretation of the Seismic Behavior

The paper's finding that the out-of-plane stiffness is relatively low is a key point. The arch bridge is primarily a two-dimensional structure, and the out-of-plane direction is often the weakest. Under a seismic load, the out-of-plane vibration can cause large displacements and a significant increase in the bending moments in the arch ribs. The time-history analysis showed that the maximum internal forces and deformations occur at different locations for different acceleration peaks, which means that the design must consider multiple load combinations.

The use of the "unified theory" is a simplification, but it is a practical one. The CFST section is modeled as a single material with an equivalent stiffness and strength. This approach is valid for the elastic range, but it may not accurately capture the inelastic behavior under a rare earthquake. The paper's conclusion that the CFST structure maintains sufficient ductility is reassuring, but it is based on the assumption that the steel-concrete interface bond is intact. In reality, the bond can degrade under cyclic loading, which can lead to a reduction in the composite stiffness.

Manufacturing and Fabrication Implications

The fabrication of the arch ribs is a complex process. The pipe must be bent to the arch profile, which is typically done by induction bending or cold bending. Induction bending is preferred for large-diameter pipe because it allows for a tighter bend radius without causing excessive ovality. However, induction bending introduces a heat-affected zone (HAZ) that can have different mechanical properties than the base metal. The HAZ must be carefully controlled to avoid a reduction in strength or toughness.

The welding of the arch segments is also critical. The arch is typically fabricated in segments, and the segments are welded together on site. The field welds must be full-penetration welds, and they must be inspected with ultrasonic testing to ensure that there are no defects. In my experience, the field welding of an arch bridge is a challenging operation because the welds are often in difficult positions, and the weather conditions can affect the weld quality. The paper's recommendation to consider multiple load combinations is a reminder that the design must account for the actual construction sequence and the residual stresses from welding.

Key Lessons and Reflection

The paper provides a valuable seismic analysis of a CFST arch bridge, but the real lesson for a manufacturer is that the fabrication of the arch ribs is a high-risk operation. The bending of the pipe and the welding of the segments must be carefully controlled to ensure that the structural integrity is maintained. The paper's conclusion that the CFST structure has excellent seismic performance is reassuring, but it is based on the assumption that the fabrication is of high quality. In my view, the arch ribs should be fabricated with a tolerance of no more than 5mm on the arch profile, and the field welds should be 100% inspected with ultrasonic testing. The residual stresses from the bending and welding should be relieved by a post-weld heat treatment, or at least by a controlled peening process.