Quenching Unit Modification for Steel Pipe: The Combined External Spray, Internal Spray, Semi-Immersion, and Rotation System
The Evolution of Quenching Methods and Their Limitations
The paper by Ma Hui and colleagues from China Heavy Machinery Research Institute and Jingjiang Special Steel examines the modification of a quenching unit for steel pipe. This is a topic that is close to my heart because I have spent years dealing with the consequences of poor quenching: inconsistent hardness, distortion, residual stress, and the resulting scrap and rework.
The paper begins by analyzing the two conventional quenching methods: tank quenching and external spray quenching. Tank quenching involves immersing the pipe in a quench tank filled with water or oil. External spray quenching involves spraying the quenchant onto the outside of the pipe as it rotates. Both methods have limitations that become more severe as the pipe diameter and wall thickness increase.
| Method | Advantages | Limitations |
|---|---|---|
| Tank quenching | Simple, uniform cooling for small pipes | Non-uniform cooling for large pipes; vapor blanket effect; distortion |
| External spray quenching | Better control of cooling rate | Does not cool the inside of the pipe; uneven cooling for thick walls |
The paper identifies the fundamental problem: for thick-wall pipe, the outside cools faster than the inside, creating a temperature gradient that causes distortion and residual stress. The inside of the pipe may not cool fast enough, resulting in insufficient hardness in the interior wall.
The New Combined System: External Spray + Internal Spray + Semi-Immersion + Rotation
The Innovative Approach
The paper proposes a new system that combines four elements: external spray, internal spray, semi-immersion, and rotation. This is a significant departure from the conventional methods because it addresses both the inside and outside of the pipe simultaneously.
| Component | Function | Benefit |
|---|---|---|
| External spray | Cools the outer surface | Controls the cooling rate of the outer wall |
| Internal spray | Cools the inner surface | Eliminates the temperature gradient across the wall |
| Semi-immersion | Partially immerses the pipe in the quench tank | Provides additional cooling and supports the pipe |
| Rotation | Rotates the pipe during quenching | Ensures uniform cooling around the circumference |
The Semi-Immersion Concept
The semi-immersion concept is particularly interesting. The pipe is partially submerged in the quench tank, and the external spray nozzles are positioned above the water level. This means that the pipe is cooled by both the spray and the immersion, which provides a more uniform cooling rate than either method alone.
The semi-immersion also has a practical benefit: it supports the pipe during quenching, reducing the risk of sagging or distortion. Large-diameter, thick-wall pipes are heavy, and if they are not supported properly during quenching, they can deform under their own weight.
The Rotation Concept
The rotation is critical for ensuring uniform cooling around the circumference. Without rotation, the pipe cools faster on the side facing the spray nozzles and slower on the opposite side. This creates a temperature gradient that causes the pipe to bow or ovalize. The rotation ensures that every point on the pipe surface is exposed to the same cooling conditions.
Technical Analysis of the Quenching Process
The Metallurgical Requirements
The quenching process must achieve the desired microstructure and hardness throughout the wall thickness. For carbon steel and low-alloy steel pipe, the goal is typically to transform the austenite to martensite or bainite, depending on the grade and the application.
| Steel Grade | Typical Hardness After Quenching | Required Cooling Rate |
|---|---|---|
| 20# (0.20% C) | 30–40 HRC | 50–100°C/s |
| 45# (0.45% C) | 50–60 HRC | 100–150°C/s |
| 42CrMo | 45–55 HRC | 80–120°C/s |
| 27SiMn | 40–50 HRC | 70–110°C/s |
The cooling rate must be high enough to avoid the formation of pearlite or ferrite, which would reduce the hardness and the strength. However, the cooling rate must not be so high that it causes cracking or excessive distortion.
The Temperature Gradient Problem
The paper's key insight is that the temperature gradient across the wall thickness is the main cause of distortion and residual stress. In a thick-wall pipe, the outside cools rapidly, while the inside cools slowly. The outer layers contract more than the inner layers, creating a tensile stress on the outside and a compressive stress on the inside.
| Wall Thickness | Temperature Gradient ( |
|---|
Zhuojin Pipe Fitting Co., Ltd