ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Controlled Cooling Technology in Hot-Rolled Steel Pipe Production

Principles and Development of Controlled Cooling

The paper by Lü Weidong, Cheng Jiefeng, and Tang Guangbo from Baosteel and the Central Iron and Steel Research Institute provides a timely review of controlled cooling technology and its application in hot-rolled steel pipe production. The authors trace the development of controlled cooling from its origins in plate rolling to its current state, where ultra-fast cooling (UFC) is recognized as a key technology for improving the mechanical properties of hot-rolled products.

The basic principle of controlled cooling is straightforward: after hot rolling, the steel is cooled at a controlled rate to a specific temperature, and then held at that temperature or cooled further at a different rate. The cooling path determines the transformation products, which in turn determine the final microstructure and mechanical properties. For steel pipe, the key transformation is from austenite to ferrite, pearlite, bainite, or martensite, depending on the cooling rate and the steel composition.

The development of controlled cooling can be summarized in three stages:

Stage Technology Cooling Rate Application
First generation Laminar cooling 10–30°C/s Plate and strip rolling
Second generation Accelerated cooling 30–80°C/s Plate rolling, some pipe applications
Third generation Ultra-fast cooling (UFC) 100–300°C/s Plate, strip, and pipe rolling

The third generation, UFC, is the focus of the paper. UFC achieves cooling rates of 100–300°C/s by using high-pressure water jets that impinge on the hot surface, creating a thin film of water that evaporates rapidly and removes heat at a very high rate. The key advantage of UFC is that it can produce a fine-grained microstructure with improved strength and toughness, while using lower alloying additions than conventional processing.

Application in Hot-Rolled Steel Pipe Production

The application of controlled cooling to hot-rolled steel pipe is more challenging than to plate or strip, because the pipe has a circular cross-section and the cooling must be uniform around the circumference. The paper discusses several approaches, including:

  1. External cooling. The pipe is cooled by water sprays or water jets directed at the outer surface. This is the most common approach, but it requires careful design to ensure uniform cooling around the circumference.
  2. Internal cooling. The pipe is cooled by water flowing through the bore. This is more effective for thick-wall pipe, but it requires a water supply and drainage system.
  3. Combined external and internal cooling. This provides the most uniform cooling, but it is the most complex and expensive.

The paper reports that UFC has been successfully applied to hot-rolled seamless pipe for line pipe applications, achieving yield strengths of 500–600 MPa with excellent toughness. The key to success is controlling the cooling rate and the final cooling temperature. For a typical API 5L X70 grade, the recommended process is:

Practical Challenges and Future Directions

The paper is optimistic about the future of UFC in pipe production, but my own experience suggests that there are significant practical challenges that must be overcome. The most critical is uniformity of cooling. If the pipe is not cooled uniformly around the circumference, the microstructure will vary from one side to the other, leading to variations in strength and toughness that can cause problems during subsequent processing or in service.

I have seen this problem firsthand. On one project, a batch of X70 line pipe was produced with UFC, but the cooling was not uniform because the pipe was rotating slowly during cooling. The result was a circumferential variation in yield strength of 80 MPa, which was outside the acceptable range. The pipe had to be rejected, and the cooling system had to be redesigned to ensure uniform water distribution.

Another challenge is the interaction between controlled cooling and the subsequent straightening operation. Hot-rolled pipe is often straightened after cooling to correct for ovality and bow. If the controlled cooling produces a hard, high-strength material, the straightening force must be increased, which can introduce residual stresses that affect the pipe's performance.

The paper correctly identifies that UFC has a bright future in pipe production, but it also notes that the technology is still in the early stages of industrial application. The key to success will be the development of robust cooling systems that can deliver uniform cooling at high rates, combined with process control systems that can maintain the cooling parameters within tight tolerances.

Summary and Recommendations

This paper is a valuable contribution to the literature on controlled cooling in pipe production. It provides a clear overview of the technology, its principles, and its potential applications, and it correctly identifies UFC as a key technology for improving the properties of hot-rolled pipe. From a practical standpoint, the message is clear: controlled cooling, and especially UFC, offers a significant opportunity to improve the strength and toughness of hot-rolled pipe, but it requires careful process design and robust equipment. My recommendation to any pipe producer considering this technology is to invest in a cooling system that can deliver uniform cooling around the circumference, and to validate the process with a rigorous trial program before committing to full production. The rewards are substantial, but the risks of getting it wrong are equally substantial.