Lateral Local Compression Performance of Square Hollow Sandwich Steel Tube Concrete Members
Literature Overview and Core Findings
This paper by Yang Youfu and Meng Chunyuan from Dalian University of Technology investigates the lateral local compression behaviour of square hollow sandwich steel tube concrete members. The authors used ABAQUS to build a nonlinear finite element model and conducted tests on six specimens with varying bearing plate to outer side length ratios and hollow ratios. The results show that the members have good mechanical performance under lateral local compression, and the finite element model agrees well with the test data.
The hollow sandwich section is an interesting structural form. It consists of an outer steel tube, an inner steel tube, and a concrete layer in between. This configuration provides high bending stiffness with a relatively low weight, making it attractive for applications where the member is subjected to lateral loads, such as in bridge piers or building columns. The lateral local compression scenario arises when a bearing plate is placed on the side of the member, such as at a connection or a support.
Technical Points and Process Interpretation
The lateral local compression behaviour is governed by a combination of the steel tube's confinement and the concrete's compressive strength.
| Parameter | Influence on Lateral Local Compression | Practical Relevance |
|---|---|---|
| Bearing plate to outer side length ratio | Higher ratio increases the loaded area and the capacity | Determines the size of the bearing plate |
| Hollow ratio | Higher ratio reduces the concrete area and the capacity | Affects the section's efficiency and weight |
| Concrete strength | Higher strength increases the local compression capacity | Drives the concrete mix design |
| Steel tube wall thickness | Thicker wall provides more confinement and higher capacity | Affects the steel plate selection |
| Bearing plate thickness | Must be adequate to distribute the load without bending | Affects the connection design |
The failure mode under lateral local compression is typically a combination of concrete crushing and steel tube yielding. The concrete is confined by the outer tube, which increases its apparent compressive strength. The inner tube provides additional restraint, but its effect is smaller because it is further from the loaded area. The paper's finite element model captures this behaviour well, and the test results confirm the trends.
The hollow ratio is a key parameter. A higher hollow ratio means less concrete, which reduces the capacity. However, it also reduces the weight, which may be beneficial in some applications. The engineer must balance these competing effects. The bearing plate ratio is also important: a larger plate spreads the load over a larger area, reducing the local stress and increasing the capacity.
Engineering Practice and Lessons Learned
I have seen hollow sandwich steel tube concrete members used in bridge construction, and the lateral local compression issue is a critical design consideration.
First, the bearing plate must be designed carefully. If the plate is too thin, it will bend under the load, and the load will not be distributed evenly. This can cause a premature failure at the edge of the plate. I have seen this happen on a bridge where the bearing plate was specified as 20 mm thick, but the actual load was higher than expected, and the plate deformed visibly. The fix was to increase the plate thickness to 30 mm and add stiffeners.
Second, the concrete fill quality is critical. If the concrete is not placed properly, there may be voids or honeycombing, which reduces the local compression capacity. The paper's finite element model assumes a homogeneous concrete, but in practice, the concrete may not be uniform. The engineer should specify a concrete placement procedure that ensures complete filling and good compaction.
Third, the hollow ratio must be checked against the actual loading. A high hollow ratio may be attractive for weight savings, but it reduces the capacity. The engineer must ensure that the capacity is adequate for the worst-case loading scenario, not just the average. This is a common mistake in design: optimising for weight without checking the ultimate capacity.
Summary and Reflection
This paper provides a valuable contribution to the understanding of lateral local compression in square hollow sandwich steel tube concrete members. The finite element model is well-validated, and the parametric study provides useful design guidance. For the practising engineer, the key takeaways are that the bearing plate ratio and the hollow ratio are the primary parameters, the concrete quality is critical, and the finite element model can be used to develop design formulas. The paper does not provide a simple design formula, but it provides the tools to develop one. I would recommend this paper to any engineer involved in the design of hollow sandwich steel tube concrete members, with the caveat that the bearing plate must be designed to distribute the load evenly, and the concrete placement must be carefully controlled.
Zhuojin Pipe Fitting Co., Ltd