Low-Hardness P91 Steel Pipe Fittings: Analysis of Brinell Hardness Conversion Value Deviation
Literature Overview
This paper by Yang Chao, Tang Chunpo, and Sun Xiong from Jiangsu Fangtian Electric Power Technology Co., Ltd. and Guodian Taizhou Power Generation Co., Ltd. addresses a problem that has caused significant headaches in the power generation industry: the deviation between Leeb hardness measurements and actual Brinell hardness values in low-hardness P91 steel pipe fittings. The authors conducted hardness comparison tests on P91 and low-alloy steel pipe fittings with different hardness levels, eliminating external factors such as specimen temperature, rigidity, mass, and surface condition. They then analyzed the internal causes of the deviation based on mechanical property test results, the principles of Leeb hardness testing, and strengthening theory.
This is a topic that I have encountered many times in my career, particularly when supplying P91 pipe fittings for power plant applications. P91 is a high-chromium ferritic steel that is widely used in supercritical and ultra-supercritical boiler applications, and its hardness is often used as a surrogate for strength verification. The fact that the conversion values can be significantly off in low-hardness material is a serious quality control concern.
Key Technical Points
Hardness Testing Methods and Conversion
The paper focuses on the relationship between Leeb hardness (HLD) and Brinell hardness (HB). The Leeb hardness test is a rebound test that measures the ratio of rebound velocity to impact velocity, while the Brinell test measures the diameter of an indentation. The conversion between the two is based on empirical relationships that assume a certain relationship between the material's elastic modulus and its strength.
| Hardness Method | Measurement Principle | Typical Application |
|---|---|---|
| Leeb (HLD) | Rebound velocity ratio | Portable testing, field inspection |
| Brinell (HB) | Indentation diameter | Laboratory testing, reference method |
| Rockwell (HRC) | Indentation depth | Hardness testing of thin sections |
| Vickers (HV) | Indentation diagonal | Micro-hardness testing, weld HAZ |
Root Cause of the Negative Deviation
The key finding is that the negative deviation in the Brinell hardness conversion value (HBHLD) for low-hardness P91 pipe fittings is primarily caused by a reduction in the yield-to-tensile ratio (屈强比). As the hardness of the P91 steel decreases, the solid solution strengthening and dislocation strengthening effects weaken, leading to a lower yield-to-tensile ratio. This changes the relationship between the rebound velocity and the indentation size, causing the conversion value to be lower than the actual Brinell hardness.
The paper also notes that the elastic modulus has a minor effect on the conversion, which is consistent with the fact that the elastic modulus of P91 steel is relatively stable regardless of heat treatment condition.
Mechanical Property Correlation
The relationship between hardness and strength is well-established for many steels, but P91 is a special case because its hardness is highly sensitive to the heat treatment condition. The paper's findings suggest that the conversion tables used for hardness testing may need to be adjusted for P91 steel, particularly in the low-hardness range.
Connection to Manufacturing and Delivery Practice
Quality Control in Pipe Fitting Manufacturing
In my experience, P91 pipe fittings are typically manufactured by forging or extrusion, followed by heat treatment. The heat treatment process is critical for achieving the required mechanical properties, and hardness testing is often used as a quick verification method. However, this paper highlights a potential pitfall: if the hardness conversion value is used as the acceptance criterion, low-hardness material may be incorrectly rejected or accepted.
| Inspection Stage | Test Method | Acceptance Criterion | Risk |
|---|---|---|---|
| After heat treatment | Leeb hardness (portable) | Converted HB value | Conversion may be inaccurate for low hardness |
| After heat treatment | Brinell hardness (laboratory) | Direct HB value | Reference method, but requires sample preparation |
| Final inspection | Leeb hardness (portable) | Converted HB value | Same conversion risk |
Case Study: Power Plant Pipe Fitting Rejection
I recall a specific case where a batch of P91 pipe fittings was rejected based on Leeb hardness measurements that indicated a Brinell hardness below the specified minimum. The supplier argued that the material was actually within specification, and laboratory testing confirmed that the actual Brinell hardness was acceptable. The issue was traced back to the conversion table, which was not appropriate for the specific heat treatment condition of the material.
This case illustrates the importance of understanding the limitations of hardness conversion. In practice, we should always confirm questionable results with direct Brinell or Vickers testing, particularly for critical applications such as power plant piping.
Heat Treatment and Microstructure
The paper's finding that the yield-to-tensile ratio decreases with lower hardness is related to the microstructure of P91 steel. In the normalized and tempered condition, P91 has a tempered martensite structure with fine precipitates that provide both solid solution and dislocation strengthening. If the tempering temperature is too high or the holding time is too long, the precipitates coarsen, and the strengthening effects weaken.
| Heat Treatment Condition | Microstructure | Yield-to-Tensile Ratio | Hardness |
|---|---|---|---|
| Normalized + tempered at 730-750°C | Tempered martensite | High (0.85-0.90) | High (220-250 HB) |
| Over-tempered (above 780°C) | Coarsened precipitates | Lower (0.75-0.80) | Lower (180-200 HB) |
| Under-tempered (below 720°C) | Untempered martensite | High but brittle | High but brittle |
Key Questions and Reflections
- Why does the deviation only appear in low-hardness P91? The answer lies in the relationship between hardness and yield strength. In the high-hardness range, the yield-to-tensile ratio is relatively stable, and the conversion tables are accurate. In the low-hardness range, the yield-to-tensile ratio drops, and the conversion becomes less reliable.
- Should the conversion tables be revised for P91 steel? This is a question that the industry needs to address. The current conversion tables are based on general-purpose relationships that may not be accurate for all steel grades. For P91, a dedicated conversion relationship may be needed.
- What is the practical impact on quality control? If the conversion value is used as the acceptance criterion, there is a risk of rejecting acceptable material or accepting unacceptable material. This could lead to unnecessary delays or, worse, the installation of material that does not meet the specified properties.
Study Insights and Implications
This paper provides a valuable contribution to the understanding of hardness testing in P91 steel. The key insights are:
- The Leeb-to-Brinell hardness conversion is not universally accurate for P91 steel, particularly in the low-hardness range.
- The deviation is primarily caused by changes in the yield-to-tensile ratio, which are related to the heat treatment condition and microstructure.
- Quality control procedures should include direct Brinell or Vickers testing for critical applications, rather than relying solely on conversion values.
From a manufacturing perspective, this paper highlights the importance of understanding the limitations of inspection methods. We should always be cautious when using portable hardness testers for acceptance decisions, and we should verify results with laboratory testing when there is any doubt.
Reference Value and Outlook
This research is particularly relevant to the power generation industry, where P91 pipe fittings are used in high-temperature, high-pressure applications. The findings should be incorporated into quality control procedures and inspection standards.
Looking ahead, I would expect to see further research on the development of grade-specific hardness conversion relationships. This would improve the accuracy of portable hardness testing and reduce the need for laboratory testing in the field.
In my experience, the most effective approach is to combine portable hardness testing with occasional laboratory verification. This provides a balance between speed and accuracy, and it ensures that the material meets the specified requirements.
Zhuojin Pipe Fitting Co., Ltd