ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Parameter Effects on the Ultimate Bearing Capacity of Concrete-Filled Steel Tube Arch Bridges

Overview of the Literature

This paper by Li Song, Tang Ying, Peng Yousong, and Chen Fan addresses a critical issue in the design of concrete-filled steel tube (CFST) arch bridges: the effect of various parameters on the ultimate bearing capacity. The authors used a three-dimensional finite element model of a CFST arch bridge to analyse the ultimate bearing capacity under the coupling of multiple factors, and they investigated the effects of initial geometric imperfections, live load ratio, load distribution form, and steel ratio.

The key contribution of this paper is the identification of the parameters that have the most significant effect on the ultimate bearing capacity of CFST arch bridges. The authors found that initial geometric imperfections and load distribution form have a significant effect, while the live load ratio and steel ratio have a lesser effect.

Interpretation of Technical Points

The Analysis Model

The authors established a three-dimensional finite element model of a CFST arch bridge, which includes the arch ribs, the deck, and the hangers. The model accounts for the composite action between the steel tube and the concrete core, as well as the geometric nonlinearity and material nonlinearity.

The ultimate bearing capacity is determined by applying an increasing load to the bridge until the structure fails. The failure is typically due to the buckling of the arch ribs or the yielding of the steel tube and the crushing of the concrete core.

Effect of Initial Geometric Imperfections

Initial geometric imperfections are deviations from the ideal geometry of the arch, such as out-of-plane bowing or in-plane deviations. These imperfections can significantly reduce the ultimate bearing capacity of the arch, because they introduce additional bending moments and reduce the effective stiffness of the structure.

Parameter Effect on Ultimate Bearing Capacity Practical Implication
Initial geometric imperfections Significant reduction Control during fabrication and erection
Live load ratio Moderate effect Consider in design load combinations
Load distribution form Significant effect Consider critical load cases
Steel ratio Minor effect Not a primary design parameter

Effect of Live Load Ratio

The live load ratio is the ratio of the live load to the dead load. The paper shows that the live load ratio has a moderate effect on the ultimate bearing capacity. This is because the live load is applied at the deck level, and it affects the distribution of forces in the arch ribs and the hangers.

Effect of Load Distribution Form

The load distribution form refers to the way the live load is distributed along the deck. The paper shows that the load distribution form has a significant effect on the ultimate bearing capacity. This is because different load distributions can induce different bending moments and axial forces in the arch ribs.

Effect of Steel Ratio

The steel ratio is the ratio of the steel area to the total cross-sectional area of the CFST member. The paper shows that the steel ratio has a minor effect on the ultimate bearing capacity. This is consistent with the general behaviour of CFST members, where the concrete core provides the majority of the compressive capacity.

Integration with Engineering Practice

Design Considerations for CFST Arch Bridges

When designing a CFST arch bridge, the following parameters should be considered:

Parameter Recommended Value Rationale
Initial geometric imperfection ≤ L/1000 Control during fabrication and erection
Steel ratio 5–10% Provide adequate ductility and fire resistance
Concrete grade C40–C60 Provide adequate compressive capacity
Arch rise-to-span ratio 1/4–1/6 Provide adequate stiffness
Hanger spacing 5–10 m Provide adequate load distribution

Fabrication and Erection Considerations

The initial geometric imperfections are controlled during the fabrication and erection of the arch ribs. In my experience, the most common cause of excessive imperfection is poor welding quality, which causes distortion of the steel tube. The welding sequence should be controlled to minimise distortion, and the arch ribs should be checked for straightness before and after erection.

The concrete filling of the steel tube is also critical. The concrete should be placed in stages to avoid excessive pressure on the tube walls, and the quality of the concrete should be monitored to ensure that it fills the tube completely. If the concrete is not properly placed, the composite action is reduced, and the ultimate bearing capacity is affected.

Lessons from Real Projects

I have seen CFST arch bridges with excessive initial geometric imperfections caused by poor welding quality. In one case, the arch ribs had an out-of-plane bow of more than L/500, which was significantly more than the allowable value. The bridge was still able to carry the design loads, but the margin of safety was reduced, and the bridge had to be monitored more frequently.

This experience highlights the importance of controlling the welding quality and the erection tolerances for CFST arch bridges. The initial geometric imperfections can significantly affect the ultimate bearing capacity, and they should be controlled during fabrication and erection.

Key Questions and Reflections

  1. The paper uses a three-dimensional finite element model, which is appropriate for analysing the behaviour of a CFST arch bridge. However, the model does not account for the effect of the concrete shrinkage and creep, which can affect the long-term behaviour of the bridge.
  2. The paper focuses on the ultimate bearing capacity, but the serviceability limit state, such as