ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Dynamic Characteristics of a Large-Span CFST Arch Bridge During Construction Based on Tower-Cable-Arch Integrated Modeling

Overview of the Study

This paper from Chongqing Jiaotong University addresses a critical issue in the construction of large-span concrete-filled steel tube (CFST) arch bridges: the dynamic characteristics of the structure during the construction phase. The authors used the finite element software ANSYS to build an integrated model of the tower, cables, and arch rib for the Hejiang Yangtze River No. 1 Bridge, which at the time was the largest span CFST arch bridge in the world. They compared this integrated model (Model 1) with a simplified model that did not include the tower (Model 2) and analyzed the dynamic characteristics, including natural frequencies and mode shapes. The study is important because the construction phase is the most vulnerable period for a large-span arch bridge, and the interaction between the temporary tower, the cables, and the arch rib can significantly affect the dynamic response and the stability of the structure.

Key Technical Findings

The most significant finding is that when the tower is included in the model, the fundamental frequency of the structure decreases by 12% compared to the model without the tower. This means that the tower-cable-arch interaction has a softening effect on the overall structure, which is counterintuitive but important. The tower adds mass and flexibility, and the cables, which are tensioned, can either stiffen or soften the structure depending on their tension and orientation. The study also found that the arch rib and the tower are coupled, and the higher-order mode shapes are complex, involving both the arch and the tower. This coupling means that a dynamic excitation at one part of the structure can induce significant response in another part, which is a risk during construction, especially under wind loading. The transverse stiffness of the structure is weak, which makes it more sensitive to wind. This is a critical finding for a bridge under construction, because the wind can induce large oscillations in the arch rib before it is fully connected. The study also found that the frequencies of the two models converge after the 30th mode, and that changes in the cable forces have little effect on the low-order frequencies. This suggests that the low-order dynamic behavior is dominated by the arch rib and the tower, not by the cable tensions.

Engineering Practice Insights

In my experience with large-scale steel structures, the construction phase is where most problems occur. The study's finding that the tower-cable-arch interaction reduces the fundamental frequency by 12% is a red flag for construction engineers. If the design calculations do not account for this interaction, the structure may be more flexible than expected, and the wind-induced vibrations may be larger than predicted. I have seen cases where temporary structures were designed without considering the interaction with the main structure, leading to excessive vibration and even failure. The coupling between the arch rib and the tower is particularly dangerous during the erection of the arch, because the cables are used to adjust the position of the arch segments, and the tower can sway, causing the cables to slacken or over-tension. This can lead to a loss of control and a collapse. The weak transverse stiffness is also a concern. During construction, the arch rib is often not laterally supported, and the wind can cause large lateral deflections. The study recommends that the transverse stiffness be increased, perhaps by adding temporary lateral bracing or by adjusting the cable arrangement. The finding that cable force changes have little effect on low-order frequencies is useful for monitoring. It means that the natural frequency is not a good indicator of cable tension, so engineers must use other methods, such as direct tension measurement, to verify the cable forces.

Reflections and Recommendations

This study is a valuable reminder that the construction phase of a large-span bridge is a complex dynamic system that must be modeled as a whole, not as isolated components. The integrated tower-cable-arch model is essential for accurate prediction of the dynamic behavior. However, the study has limitations. It only considers the free vibration characteristics, not the forced vibration response to wind or seismic loads. The damping of the structure is not addressed, which is critical for predicting the amplitude of vibrations. I would like to see a follow-up study that includes the wind load and the damping, and that performs a time-history analysis to predict the actual dynamic response during construction. In practice, I recommend that construction engineers use an integrated model for the design of the temporary structures and the erection sequence. The model should be updated as the construction progresses, and the cable forces should be monitored in real time. The wind speed at the site should be monitored, and construction should be halted if the wind exceeds a safe threshold. The study also highlights the importance of considering the transverse stiffness. In my experience, adding temporary lateral bracing to the arch rib during construction is a simple and effective way to mitigate the wind-induced vibrations. In summary, this study provides essential insights for the safe construction of large-span CFST arch bridges, but the industry must extend this work to include forced vibration analysis and to develop practical monitoring and control strategies.