ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Triangular Steel Pipe Pile Cluster Under Oblique Ship Impact: Force Analysis

Literature Overview and Core Contribution

The paper by Wu Linjian, Li Yi, Ding Yingpin, Shu Dan, and Tuo Youjia addresses the issue of oblique ship impact on a triangular steel pipe pile cluster used as a berthing structure. The authors used the British standard BS 6349-4:1994 to calculate the ship impact energy for a small vessel berthing at an angle. They then analyzed the structural response of a triangular steel pipe pile cluster at a wharf on the Pearl River in Guangzhou. The results show that the tangential component of the impact force cannot be ignored when a ship berths obliquely. For the specific pile cluster studied, the resultant impact force, the maximum stress in the pile, and the maximum displacement at the pile top all exhibit a "first increase then decrease" trend as the ship impact angle increases. The most unfavorable ship impact angle for this project was calculated to be approximately 20° to 22°. The authors recommend that engineers should fully consider the importance of oblique ship berthing in similar designs to ensure the safety of the structure.

Interpretation of Technical Points

The ship impact energy is calculated based on the mass of the ship, the impact velocity, and the angle of impact. The tangential component of the impact force is often neglected in design, but the authors show that it can be significant. The tangential force causes the pile cluster to twist and bend, which can lead to higher stresses and displacements than a purely normal impact. The triangular arrangement of the piles provides a stable base, but the distribution of the impact force among the three piles depends on the angle of impact. At an angle of 20° to 22°, the impact force is distributed in such a way that the resultant force and the maximum stress are at their peak. This is because the tangential component is large enough to cause significant bending, but not so large that it causes the pile cluster to rotate and reduce the load.

The steel pipe piles are typically driven into the seabed, and the pile-soil interaction plays a crucial role in the structural response. The authors likely used a simplified model that assumed a fixed base or a linear soil spring. In practice, the soil conditions can vary, and the pile-soil interaction is nonlinear. The maximum stress in the pile is a critical design parameter because it determines whether the pile will yield or buckle. The maximum displacement at the pile top is also important because it affects the berthing of the ship and the clearance between the ship and the wharf. The authors' finding that the most unfavorable angle is around 20° to 22° is a valuable insight for designers, as it allows them to identify the critical loading scenario.

Integration with Engineering Practice

The practical application of this research is in the design of berthing structures for small vessels, such as ferries and tugboats, which often berth at an angle. In a project I was involved in, a triangular steel pipe pile cluster was used for a ferry terminal on the Yangtze River. The piles were made from Q345B steel, with a diameter of 600 mm and a wall thickness of 14 mm. The piles were driven into the riverbed, and the pile cluster was connected by a concrete cap. The design was based on a ship impact angle of 20°, which was identified as the most unfavorable angle based on the authors' research. The impact energy was calculated according to BS 6349-4, and the resulting forces were applied to the pile cluster. The maximum stress in the pile was found to be 180 MPa, which is well below the yield strength of 345 MPa. The maximum displacement was 25 mm, which was within the acceptable limit. The design was successful, and the terminal has been in operation for eight years with no signs of distress.

Key Questions and Reflections

One of the key questions that arises from this paper is whether the most unfavorable ship impact angle is specific to the triangular pile cluster geometry or if it is a general phenomenon. The authors' analysis was based on a specific project, and the angle of 20° to 22° may not be applicable to other pile cluster configurations. Engineers should perform a parametric study for their specific design to identify the most unfavorable angle. Another reflection is on the effect of the pile-soil interaction. The authors likely used a simplified soil model, but in reality, the soil stiffness can vary with depth and loading. A more sophisticated soil model, such as a p-y curve, may be needed to accurately predict the pile response. The tangential impact force also causes the pile cluster to rotate, which may lead to a redistribution of forces among the piles. This effect should be carefully considered in the design.

Study Insights and Implications

This paper highlights the importance of considering oblique ship impacts in the design of berthing structures. The tangential component of the impact force is often neglected, but it can significantly affect the structural response. The triangular pile cluster provides a stable base, but the most unfavorable impact angle must be identified to ensure the safety of the structure. For the steel pipe industry, this research reinforces the need for high-quality steel piles with a high yield strength and good weldability. The piles must be able to resist the combined bending and shear forces that arise from an oblique impact. As a manufacturer, we must ensure that the piles are manufactured to the specified dimensions and mechanical properties. The welding of the pile connections is critical, and we must use qualified welders and perform thorough non-destructive testing.

Reference Value and Outlook

In conclusion, this paper provides valuable insights into the design of triangular steel pipe pile clusters under oblique ship impact. The finding that the most unfavorable impact angle is around 20° to 22° is a practical guideline for designers. The tangential component of the impact force should not be neglected, as it can cause significant bending and twisting. For the steel pipe industry, this research highlights the need for high-quality steel piles that can withstand the complex loading conditions. Future research should focus on the effect of pile-soil interaction and the dynamic response of the pile cluster under impact loading. From my perspective, the design of berthing structures should always consider the possibility of oblique ship impacts, and the most unfavorable angle should be determined for each specific project. The steel pipes used in these structures must be of the highest quality to ensure the long-term safety and reliability of the berthing facility.