Principles of Concrete Pumping in Concrete-Filled Steel Tube Columns and Analysis of Pump Pressure
Literature Overview
Feng Yonggang, Wang Xin and Yang Shirong, writing in Construction Technology in 2009, address a problem that every contractor who has ever pumped concrete into a tall steel column knows intimately: how much pressure does the pump actually need, and how does that pressure change as the concrete rises through the column? The paper is based on field measurements taken at the Baosteel stainless steel project, where concrete was pumped into industrial plant steel columns. The authors instrumented the columns with pressure sensors at different heights and recorded the pressure profile during pumping. Their key finding is that the pump outlet pressure is not a steady value but a pulsating one, and they propose a method to calculate it by multiplying the steady-flow pressure by a pulse amplification factor λ.
Core Findings and Technical Interpretation
Pressure Variation with Height
The field measurements produced a clear pressure-versus-height curve. The pressure at the pump outlet is at its maximum, and it decreases as the concrete rises through the column. The pressure loss is not linear; it is influenced by the friction between the concrete and the tube wall, the concrete's rheological properties, and the height of the column. The authors found that the pressure loss per meter of height is higher in the lower portion of the column, where the concrete is fresh and has not yet begun to set, and lower in the upper portion, where the concrete has started to hydrate and gain some stiffness.
Pulsating Pressure and the Amplification Factor
The most significant contribution of this paper is the identification of the pulsating nature of the pump outlet pressure. A concrete pump operates on a reciprocating principle — the piston pushes concrete forward, then retracts, then pushes again. This creates a pressure wave that travels through the delivery line and into the column. The authors measured this pulsation and found that the peak pressure can be significantly higher than the average steady-flow pressure. They propose a pulse amplification factor λ, which is the ratio of the peak pressure to the steady-flow pressure, and they provide a method to calculate the required pump outlet pressure by multiplying the calculated steady-flow pressure by λ.
Practical Calculation Method
The proposed method is straightforward: first, calculate the steady-flow pressure required to lift the concrete to the top of the column, accounting for the weight of the concrete column and the friction losses. Then, multiply this steady-flow pressure by the pulse amplification factor λ to obtain the actual pump outlet pressure. The value of λ depends on the pump's stroke characteristics, the concrete's rheology, and the delivery line configuration. The authors do not provide a universal λ value, but they recommend that it be determined by field measurement or by consulting the pump manufacturer's data.
Engineering Practice Implications
What This Means for the Contractor and the Pipe Supplier
From my experience on industrial plant construction, the pumping of concrete into steel columns is a critical operation that often goes wrong when the contractor underestimates the pressure required. The consequences are severe: the pump stalls, the delivery line bursts, or the concrete segregates because the pumping rate is too low. The pulsating pressure is the hidden culprit. A pump that is rated for a certain maximum pressure may still fail if the pulsating peak exceeds that rating, even if the average pressure is within limits.
Practical Recommendations
- Do not rely on the pump's rated pressure alone. The rated pressure is usually the steady-flow capability. The actual peak pressure can be 20% to 40% higher. When selecting a pump, apply the amplification factor to the calculated steady-flow pressure and compare that against the pump's maximum pressure rating.
- Instrument the column during the first pump. On any project where the column height exceeds 20 meters, install pressure sensors at the pump outlet and at the top of the column. This gives you real data to calibrate the pressure loss model and to verify that the pump is adequate.
- Control the concrete rheology. The pressure loss is directly proportional to the concrete's plastic viscosity and yield stress. A concrete with too much slump will segregate and block the line; a concrete with too little slump will require excessive pressure. The target slump for pumping into steel columns should be in the range of 180 to 220 mm, with a maximum aggregate size of 20 mm.
- Consider the column geometry. The pressure loss is higher in smaller-diameter columns because the surface-area-to-volume ratio is higher, which increases the friction at the tube wall. For columns with a diameter of less than 400 mm, expect a higher pressure loss per meter of height.
Standards and Judgement
There is no dedicated Chinese standard for concrete pumping pressure in steel columns. The relevant guidance is scattered across JGJ/T 10 (concrete pumping construction) and the pump manufacturer's specifications. This paper provides a practical method that fills the gap, but it is based on a single project. I would recommend that the contractor verify the λ value on each project, because the concrete mix, the pump type, and the column geometry all influence it.
Key Questions and Reflections
The most important question this paper raises is whether the pulsating pressure can cause damage to the steel tube itself. The tube is designed to carry the axial load of the concrete and the structural loads, but it is not typically designed for internal pressure. If the pulsating pressure is high enough, it could cause local yielding or even buckling of the tube wall, especially at the base where the pressure is maximum. This is a design consideration that the structural engineer should address, and it may require stiffening rings or thicker tube walls in the lower portion of tall columns.
Another reflection: the paper does not address the effect of the concrete's setting time on the pressure profile. In a tall column, the concrete at the bottom begins to set while the concrete at the top is still being pumped. This creates a non-uniform pressure distribution that is not captured by a simple steady-flow model. The authors acknowledge this indirectly by noting that the pressure loss is higher in the lower portion, but they do not provide a method to account for the time-dependent behavior.
Study Insights and Outlook
This paper is a valuable practical contribution. It takes a problem that is often handled by guesswork and provides a systematic method based on field measurement. The pulse amplification factor λ is a simple and effective concept that can be applied immediately on any project. The next step is to develop a more comprehensive model that accounts for the time-dependent setting of the concrete and the interaction between the pulsating pressure and the tube wall. For the steel pipe industry, this paper reinforces the importance of specifying tubes with adequate wall thickness and high-quality welds for concrete-filled columns, because the internal pressure during pumping is an additional load that the tube must withstand.
In closing, I would say this: pumping concrete into steel columns is a deceptively simple operation that can turn into a disaster if the pressure is underestimated. This paper gives the contractor a practical tool to avoid that disaster, and it gives the pipe supplier a clear reason to emphasize tube quality. Read it, apply it, and you will save yourself a lot of trouble on site.
Zhuojin Pipe Fitting Co., Ltd