Internal Warping Defect in GCr15 Bearing Steel Tube During Piercing
The Defect and Its Significance in Bearing Tube Production
GCr15 is the workhorse bearing steel grade in China, corresponding to AISI 52100 in the American system. It is used for rolling element bearings, and the tube form is typically produced by hot piercing of a solid billet, followed by cold drawing or cold rolling to final dimensions. The internal surface quality of the bearing tube is critical because any defect will be carried through to the bearing raceway, where it can cause premature fatigue failure.
The paper by Peng Kewu, Lu Bingjun, Qi Feng and Wang Deyong addresses a specific defect: internal warping (内翘皮) that appears during the piercing process. This is a defect that I have encountered in production, and it is one of the most frustrating because it is often not detected until the tube has been processed through several stages. By the time the defect is found, significant value has already been added to the product.
The research team used a combination of process comparison tests, chemical composition analysis, metallographic examination, scanning electron microscopy with energy-dispersive spectroscopy, and ultrasonic testing to identify the root cause. The approach is systematic and thorough, and the findings are directly applicable to production.
Root Cause — Center Porosity Tearing During Piercing
The critical finding is that the internal warping defect is caused by severe center porosity in the bearing steel billet, which tears and extends during the piercing process. The center porosity is a solidification defect that occurs in the center of the ingot or continuously cast billet, where the last liquid to solidify is enriched in impurities and the solidification shrinkage creates voids.
| Analysis Method | Finding | Significance |
|---|---|---|
| Chemical composition | Within GCr15 specification | Not the root cause |
| Metallographic examination | Center porosity in billet | Confirms solidification defect |
| SEM + EDS | No significant inclusions at defect location | Rules out inclusion-related cause |
| Ultrasonic testing | Detectable center porosity in billet | Provides screening method |
| Process comparison | Defect correlates with billet quality | Confirms root cause |
During the piercing process, the billet is subjected to severe deformation as it is pushed over the piercing plug. The center porosity, which is already a weakness in the material, is torn open by the deformation, creating the internal warping defect. The defect is then carried through to the finished tube, where it may be detected by ultrasonic inspection or may remain undetected until the tube is machined.
The fact that no significant inclusions were found at the defect location is important. This rules out the possibility that the defect is caused by non-metallic inclusions, which are a common source of internal defects in bearing steel. The root cause is purely a solidification defect — center porosity.
Quality Control Strategy — Ultrasonic Inspection of Billets
The practical solution proposed by the authors is to use ultrasonic inspection to control the quality of the bearing steel billet before piercing. If the billet has significant center porosity, it should be rejected or diverted to a less demanding application. This is a simple and effective quality control measure that can prevent the defect from occurring.
| Inspection Stage | Method | Acceptance Criteria | Action |
|---|---|---|---|
| Billet receiving | Ultrasonic testing | No significant center porosity | Reject or downgrade |
| Before piercing | Ultrasonic testing | Confirm billet quality | Reject if defective |
| After piercing | Ultrasonic or eddy current | Detect internal defects | Reject or repair |
| Final tube | Ultrasonic testing | No internal defects | Accept or reject |
The key insight here is that the quality control should be applied at the earliest possible stage. Once the billet is pierced, the defect is already formed, and the only option is to reject the tube. By inspecting the billet before piercing, the mill can avoid the cost of processing a defective billet through the entire production line.
From a production perspective, the ultrasonic inspection of billets is a well-established practice in the bearing steel industry. The challenge is ensuring that the inspection is performed consistently and that the acceptance criteria are appropriate. If the acceptance criteria are too strict, good billets may be rejected, increasing cost. If they are too lenient, defective billets may pass, and the defect will appear in the finished tube.
Production Lessons and Recommendations
The research highlights a fundamental principle in steel tube production: the quality of the final product is determined by the quality of the raw material. No amount of downstream processing can compensate for a defective billet. This is a lesson that I have learned many times in my career, and it is worth repeating.
The practical recommendations for bearing steel tube producers are:
- Implement ultrasonic inspection of billets as a mandatory quality control step before piercing. The inspection should be performed on 100% of billets, not just a sample.
- Establish clear acceptance criteria for center porosity based on the ultrasonic inspection results. The criteria should be based on the severity of the porosity and the intended application of the tube.
- If a defective billet is detected, reject it and investigate the root cause. The center porosity is a solidification defect, and its presence may indicate problems in the steelmaking or continuous casting process.
- Monitor the incidence of center porosity over time to detect trends. If the incidence increases, investigate the upstream process to identify the cause.
There is also a commercial dimension to consider. Bearing steel tube is a high-value product, and the cost of a rejected tube is significant. By preventing the defect at the billet stage, the mill can improve its yield and reduce its cost. This directly improves the profitability of the operation.
In my experience, the most effective quality control systems are those that focus on prevention rather than detection. The ultrasonic inspection of billets is a prevention measure — it prevents the defect from occurring in the first place. This is far more effective than trying to detect the defect after it has formed.
In conclusion, this paper provides a clear and well-supported explanation of the internal warping defect in GCr15 bearing steel tube. The root cause is center porosity in the billet, which tears during piercing. The countermeasure is ultrasonic inspection of billets before piercing. I would recommend this paper to production engineers, quality control engineers, and anyone involved in the production of bearing steel tube. The key message is simple: control the billet quality, and you control the tube quality.
Zhuojin Pipe Fitting Co., Ltd