ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Bearing Capacity Calculation Methods for High-Strength Steel Concrete-Filled Steel Tube Members

Literature Overview and Practical Significance

This paper by Yao Guohuang and Han Linhai addresses a growing problem in structural engineering: how to calculate the bearing capacity of concrete-filled steel tube (CFST) members made from high-strength steel. The authors summarise existing research, develop a numerical model to calculate the load-deformation relationship of high-strength CFST members under combined axial load and bending, verify the model against experimental results, and then compare the applicability of six design codes (DL/T 5085-1999, GJB 4142-2000(2001), AIJ 1997, EC4 1994, AISC-LRFD 1999, and DBJ 13-51-2003) for calculating the bearing capacity of high-strength CFST members.

For a steel pipe veteran, this paper is directly relevant to the procurement and fabrication of high-strength steel tubes. High-strength steel (typically Q460, Q550, Q690 or higher) is increasingly used in tall buildings and long-span structures because it allows smaller column sections and lighter steel weights. However, high-strength steel has a different stress-strain relationship than normal-strength steel: it has a higher yield strength but a lower ductility, a smaller yield plateau, and a different strain hardening behaviour. These differences affect the load-deformation relationship of the CFST member, and therefore the bearing capacity calculation.

The practical question is: can we use the same design formulas for high-strength steel that we use for normal-strength steel? The paper's answer is nuanced: it depends on the code, and some codes are more conservative than others.

Core Technical Points and Interpretation

Numerical Model and Verification

The authors use a fibre model approach, in which the cross-section is divided into small elements (fibres) and each fibre is assigned a uniaxial stress-strain relationship. The axial load and bending moment are applied incrementally, and the equilibrium and compatibility conditions are satisfied at each step. This is a standard approach for CFST members, but the authors have extended it to high-strength steel by using appropriate stress-strain relationships.

The key parameters in the model are:

Parameter Normal-Strength Steel (Q235, Q345) High-Strength Steel (Q460, Q550, Q690)
Yield strength (f_y) 235 – 345 MPa 460 – 690 MPa
Elastic modulus (E_s) 206 GPa 206 GPa (similar)
Yield plateau Long (10 – 20 × ε_y) Short or non-existent (2 – 5 × ε_y)
Strain hardening Moderate (E_st ≈ 0.02 E_s) Lower (E_st ≈ 0.01 E_s)
Ductility High (elongation > 20%) Lower (elongation 10 – 15%)
Ultimate strain 0.15 – 0.20 0.08 – 0.12

The numerical model accounts for the confinement effect of the steel tube on the concrete core. As the axial load increases, the concrete expands laterally and induces a hoop stress in the steel tube. This increases the compressive strength of the concrete, but also reduces the axial capacity of the steel tube. The model captures this interaction, which is essential for accurate bearing capacity prediction.

Comparison of Design Codes

The authors compare six design codes for their applicability to high-strength steel CFST members. The comparison is based on the calculated bearing capacity versus the experimental bearing capacity, and the key finding is that the codes differ significantly in their conservatism.

Code Country / Region Approach Applicability to High-Strength Steel
DL/T 5085-1999 China Superposition of steel and concrete capacities Conservative — underestimates capacity by 10-15%
GJB 4142-2000(2001) China (military) Similar to DL/T but with different safety factors Moderately conservative — underestimates by 5-10%
AIJ 1997 Japan Confinement-based approach Reasonably accurate — within ±5%
EC4 1994 Europe Superposition with confinement factor Reasonably accurate — within ±5%
AISC-LRFD 1999 USA Superposition with no confinement Conservative — underestimates by 15-20%
DBJ 13-51-2003 China (Fujian) Confinement-based approach Accurate — within ±3%

The key finding is that the codes that explicitly account for confinement (AIJ, EC4, DBJ) are more accurate for high-strength steel, while the codes that use simple superposition (DL/T, AISC) are conservative. This is because high-strength steel has a lower ductility and a shorter yield plateau, which means the confinement effect is more important for maintaining the steel tube's contribution to the bearing capacity.

The Confinement Factor

The confinement factor (ξ) is defined as:

ξ = (A_s × f_y) / (A_c × f_c)

where A_s and A_c are the steel and concrete areas, and f_y and f_c are the steel yield strength and concrete compressive strength. The confinement factor is a measure of how much the steel tube can confine the concrete core. For high-strength steel, the confinement factor is higher than for normal-strength steel (because f_y is higher), but the confinement effectiveness is lower (because the steel is less ductile). This is the fundamental tension that the paper addresses.

Confinement Factor (ξ) Normal-Strength Steel High-Strength Steel
0.5 Effective confinement, ductile failure Moderate confinement, less ductile
1.0 Strong confinement, very ductile Strong confinement, but reduced ductility
2.0 Over-confined, steel yields first Over-confined, steel may fracture before concrete crushes

Integration with Manufacturing and Delivery Practice

Steel Tube Procurement for High-Strength CFST Members

The use of high-strength steel in CFST members has significant implications for steel tube procurement:

Procurement Issue Normal-Strength Steel High-Strength Steel
Steel grade Q235, Q345, Q355 Q460, Q550, Q690
Availability Widely available from multiple mills Limited availability, often made-to-order
Cost per tonne Baseline 1.5 – 2.5 × baseline
Lead time 4 – 8 weeks 8 – 16 weeks
Weldability Excellent (no preheat required) Requires preheat (100-150°C), controlled heat input
Toughness Charpy V-notch ≥ 27 J at 0°C Charpy V-notch ≥ 40 J at -20°C (often required)
Dimensional tolerances Standard (ASTM A500, GB/T 6728) Tightened (often to EN 10219 or customer-specific)

The higher cost and longer lead time of high-strength steel mean that the design engineer must be confident in the bearing capacity calculation. If the code is too conservative, the column will be oversized and the cost advantage of high-strength steel is lost. If the code is too unconservative, the column may fail in a brittle manner.

Fabrication and Welding Considerations

High-strength steel tubes require careful welding procedures:

  1. Preheat: High-strength steel has a higher carbon equivalent (CE) than normal-strength steel, which increases the risk of hydrogen-induced cracking. A preheat of 100-150°C is typically required for Q460 and above.
  2. Heat input control: Excessive heat input can reduce the yield strength in the heat-affected zone (HAZ). The welding procedure must specify a maximum heat input, and the welder must be trained to comply.
  3. Filler metal selection: The filler metal must match or exceed the strength of the base metal. For Q460, an E70 or E80 electrode is required. For Q690, an E90 or E100 electrode is required.
  4. Post-weld heat treatment: For thick-walled tubes (t > 20 mm), a post-weld heat treatment (PWHT) may be required to relieve residual stresses. However, PWHT can reduce the yield strength of high-strength steel, so the temperature and time must be carefully controlled.

Quality Control and Inspection

For high-strength steel CFST members, the quality control requirements are more stringent:

Inspection Item Normal-Strength Steel High-Strength Steel
Chemical composition Standard analysis Full analysis with CE calculation
Mechanical properties Tensile test, Charpy test Tensile test, Charpy test at lower temperature
Weld inspection RT or UT on full length RT or UT on full length + MT on weld caps
Dimensional inspection Standard tolerances Tightened tolerances (wall thickness ±5%)
Surface inspection Visual Visual + MPI (magnetic particle inspection)

Key Questions and Reflections

The paper raises several questions that a production engineer must consider:

  1. Is high-strength steel cost-effective for CFST members? The higher cost per tonne is offset by the smaller cross-section, but the savings depend on the design code used. If the code is conservative, the savings may be minimal.
  2. What is the effect of residual stresses on high-strength steel tubes? Cold-formed high-strength steel tubes have higher residual stresses than normal-strength steel tubes, which can reduce the effective yield strength. The paper does not address this.
  3. How does the confinement effect change with tube wall thickness? A thicker wall increases the confinement factor, but also increases the cost. There is an optimum wall thickness for a given steel grade and concrete strength.
  4. What is the ductility of high-strength steel CFST members under cyclic loading? The paper only addresses monotonic loading. Seismic performance requires cyclic loading, which is a different problem.

Study Insights and Implications for the Industry

This paper is a valuable contribution to the design of high-strength steel CFST members. The authors have correctly identified that the confinement effect is the key to accurate bearing capacity prediction, and that the design codes which account for confinement (AIJ, EC4, DBJ) are more accurate than those that do not (DL/T, AISC). This is a practical finding that design engineers can use to select the appropriate code for their project.

From a manufacturing perspective, the paper reinforces the importance of tube quality and welding procedures. High-strength steel tubes are more expensive and more difficult to fabricate than normal-strength steel tubes, but they offer significant advantages in terms of weight and cost savings. The key is to ensure that the tube is manufactured to the required specifications and that the welding is performed to the correct procedure.

The paper also highlights the need for a closer collaboration between design engineers and manufacturers. The design engineer must specify the steel grade, tube dimensions and wall thickness based on the bearing capacity calculation, but the manufacturer must ensure that the tube can be produced to those specifications. This requires a clear communication of tolerances, quality requirements and acceptance criteria.

Concluding Remarks

The bearing capacity of high-strength steel CFST members is a complex problem that requires careful consideration of the confinement effect, the steel-concrete interaction, and the stress-strain relationship of the materials. This paper provides a rational basis for calculating the bearing capacity, and it identifies the design codes that are most suitable for high-strength steel. From a manufacturing perspective, the paper reinforces the importance of tube quality, welding procedures and quality control. High-strength steel tubes offer significant advantages in terms of weight and cost savings, but they require a higher level of manufacturing precision and quality assurance. I would recommend this paper to any engineer involved in the design or fabrication of high-strength steel CFST members, and I would encourage a closer collaboration between the design office and the production floor to ensure that the theoretical calculations are achievable in practice.