ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Flexural Capacity Calculation for Steel Tube-Steel Reinforced Concrete Members

The Design Problem

I have sat across the table from structural engineers who ask: why do we need steel tube-steel reinforced concrete members when we already have ordinary steel tube concrete? The answer is simple. In high-rise construction and heavy industrial structures, the axial loads are so large that a plain steel tube concrete column becomes impractical. The tube diameter and wall thickness grow to the point where fabrication and welding become difficult. Adding a steel bone inside the concrete core, either an I-section or a cross-section, increases the flexural capacity and the stiffness without increasing the outer dimensions. This paper by Liu Xiao and colleagues addresses a specific gap: how do we calculate the flexural capacity of these composite members when the steel bone is either I-shaped or cross-shaped?

The Proposed Calculation Method

The authors use the limit state superposition principle. This means they calculate the contribution of each component — the steel tube, the concrete core and the steel bone — separately, and then add them together. The method is straightforward and practical, which is exactly what we need on the design desk. The formulas were verified against experimental results from the literature, and the agreement was good. The key parameters are the yield strength of the steel tube and the steel bone, the compressive strength of the concrete, and the section geometry.

Component Contribution to Flexural Capacity
Steel tube Bending resistance of the tube wall
Concrete core Compression and tension resistance of the concrete
Steel bone (I or cross) Bending resistance of the bone, added at the correct lever arm

Section Shape Comparison and Economics

The most interesting part of this paper, from a practical standpoint, is the economic comparison. For the same steel consumption, the I-shaped steel bone provides a higher flexural capacity than the cross-shaped bone. This is because the I-section places more steel at the extreme fibres, where the bending stress is highest. The cross-section, on the other hand, has steel distributed more evenly, which is better for biaxial bending but less efficient for uniaxial bending.

Steel Bone Shape Flexural Capacity (same steel weight) Fabrication Complexity
I-section Higher Lower — easier to weld, easier to fit
Cross-section Lower Higher — four flanges to weld, more welding distortion risk

This is a critical insight for the fabrication shop. I have seen projects where the designer specified a cross-shaped steel bone because it looked more symmetrical, without realising that an I-section would have given the same capacity with less steel and less welding. The welding cost for a cross-section is significantly higher, and the welding distortion is harder to control. For a long column, the residual stresses from welding a cross-section can cause bowing that is difficult to straighten.

Practical Takeaways

For those of us who fabricate and supply the steel tubes and the steel bones, this paper gives us a clear message. When the client asks for a steel tube-steel reinforced concrete member, we should ask whether the steel bone is I-shaped or cross-shaped. If the loading is predominantly uniaxial bending, the I-section is the better choice. It is cheaper, easier to fabricate, and provides higher capacity for the same steel weight. If the loading is biaxial, then the cross-section may be justified, but we should make sure the designer has considered the fabrication cost and the welding distortion risk. The superposition method proposed in this paper is simple enough for a quick hand calculation, which is useful for preliminary design and for checking the output of a finite element analysis.

Study Insights and Reflections

I have been in the position of having to explain to a client why their steel bone specification was unnecessarily expensive. This paper gives me the technical justification to do that. The comparison between I-shaped and cross-shaped sections is not just an academic exercise. It is a real economic decision that affects material cost, welding time, and delivery schedule. The superposition method is a practical tool, but it relies on the assumption that the steel tube, the concrete and the steel bone all reach their limit states simultaneously. In reality, the concrete may crack before the steel yields, and the steel tube may buckle locally before it reaches its full plastic capacity. The verification against experimental results gives us confidence, but I would always apply a safety factor and check the failure mode against the actual section geometry.

Reference Value and Outlook

This paper is a valuable reference for structural engineers and for those of us who fabricate composite members. The economic comparison between I-shaped and cross-shaped steel bones is particularly useful for value engineering. As we see more high-rise buildings and heavy industrial structures using steel tube-steel reinforced concrete columns, having a reliable and simple calculation method becomes essential. The superposition approach is a good starting point, and it can be extended to other steel bone shapes and to combined axial and flexural loading. This is a practical contribution that deserves a place on the design desk.