ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Structural Stability of Concrete-Filled Steel Tube Composite Tied Arch: A Veteran's Review of Dumbbell vs. Single Rib Sections

What the Paper Delivers

Ning Guixia, Lin Pengzhen, and Zhao Yanlong from Lanzhou Jiaotong University have produced a practical stability study on a CFST composite tied arch bridge. The paper compares a single arch rib with a dumbbell-shaped section of the same span. The authors analyse the in-plane and out-of-plane stability of both forms, then run modal analyses on the whole bridge system in its completed and operational states. For a veteran who has watched these arches being erected, the paper is a direct hit on a question that keeps site engineers awake at night: which section shape gives us the best stability for the least steel?

Core Technical Points from the Construction Site

The dumbbell section is a classic solution for CFST arches. It consists of two parallel steel tubes connected by webs or plates, filled with concrete. The single rib is a simpler, larger tube. The paper's key finding is that the stability of the dumbbell section is influenced by the connection between the two tubes. The stiffness of the web plates and the spacing between the tubes determine the section's ability to resist out-of-plane buckling.

Parameter Single Rib Dumbbell Section Practical Consideration
Cross-section area Smaller Larger (two tubes + webs) Dumbbell uses more steel but provides higher moment capacity.
Out-of-plane stiffness Lower Higher (due to two tubes) The dumbbell resists lateral buckling better.
In-plane stiffness Comparable Comparable Both are governed by the axial stiffness of the tubes.
Welding complexity Simple (one tube) Complex (webs and multiple welds) More welding means more residual stress and distortion.
Concrete filling Single pump Two pumps or sequential filling Risk of unequal filling between the two tubes.

The paper's modal analysis of the whole bridge is also important. The operational state includes live loads, which change the dynamic characteristics. The authors found that the first few modes are dominated by the arch's out-of-plane vibration. This means the out-of-plane stability is the controlling factor for the design. A single rib with a large diameter might have adequate in-plane capacity, but it will be more flexible out-of-plane. The dumbbell section, with its two tubes, provides a natural solution to this problem.

Lessons from Real Erection and Delivery

I have seen the consequences of poor stability during erection. On one tied arch project, the contractor attempted to lift the entire arch as a single unit. The out-of-plane bracing was insufficient, and the arch started to twist. It took a crane and a lot of shouting to get it down safely. The paper's analysis would have predicted this. The out-of-plane stability of a single rib is much lower than that of a dumbbell section, and the erection sequence must account for this.

The welding of the dumbbell section is another area where the shop floor matters. The webs connecting the two tubes are typically welded with fillet welds. These welds are subject to high shear stresses when the section bends. If the weld quality is poor, the two tubes will act independently, and the composite action is lost. I have seen ultrasonic testing reveal lack of fusion in these web welds, leading to a costly repair. The paper's assumption of a rigid connection between the two tubes is only valid if the welds are sound.

The concrete filling process for a dumbbell section is also a challenge. The two tubes must be filled with the same concrete mix at the same rate. If one tube is filled faster, it will have a higher axial stiffness, and the section will be subjected to a bending moment during construction. This can cause the arch to deflect laterally. The paper does not address this construction-stage issue, but it is a real concern for the site engineer.

Study Insights and Practical Implications

The paper's conclusion that the dumbbell section has better out-of-plane stability is a key insight. For a tied arch bridge, the tie beam and the deck provide the in-plane restraint, but the out-of-plane restraint is often minimal. Therefore, the arch's own out-of-plane stiffness is critical. The dumbbell section, with its two tubes, provides this stiffness naturally.

For the pipe and fitting industry, this paper highlights the importance of the tube's geometry. The D/t ratio of the individual tubes in a dumbbell section is typically lower than that of a single rib. This means the tubes are less prone to local buckling, and the confinement effect on the concrete is better. However, the webs and the welds are additional components that must be fabricated and inspected. The cost of a dumbbell section is higher than a single rib, but the stability benefit may justify it.

Reference Value and Outlook

This paper is a useful reference for the preliminary design of CFST tied arch bridges. The comparison between single rib and dumbbell sections is clear and practical. However, the paper is from 2006, and the industry has moved towards more complex sections, such as the truss arch and the box section. The fundamental principles remain the same: out-of-plane stability is often the controlling factor, and the section shape must be chosen to provide adequate stiffness.

The next step for the industry is to incorporate the effects of concrete creep and shrinkage on the stability of the arch. These time-dependent effects can cause the arch to lose stiffness over time, reducing its buckling load. The paper does not address this, but it is a significant factor for long-span bridges.

In summary, this is a solid study that provides a clear comparison between two common section shapes. It is a reminder that the steel tube's geometry is not just a design parameter; it is a construction reality. The veteran's advice is to always consider the out-of-plane stability, and to never underestimate the importance of the welds that connect the components.