Cold and Hot Crack Resistance in NK-HITEN610U2 Penstock Welded Joints
Literature Overview and Context
The paper by Chen Guoxin and colleagues from Shaoyang University addresses a question that has kept many a penstock engineer awake at night: how do we predict and prevent cracking in high-strength low-alloy steel welded joints before we commit hundreds of tonnes of steel to a hydroelectric project? The authors chose NK-HITEN610U2, a quenched-and-tempered high-strength steel widely specified for penstocks in China and Japan, and systematically evaluated its cold and hot crack susceptibility from three angles: chemical composition, diffusible hydrogen content in the weld metal, and structural restraint degree. The work is concise but hits the three variables that, in my thirty years of running pipe fabrication shops and witnessing site failures, account for the overwhelming majority of cracking incidents in high-strength penstock welding. What the paper does well is to quantify each factor and then translate those numbers into practical process windows, which is exactly what a welding engineer needs before the first electrode touches the groove.
Interpretation of Core Technical Points
Chemical Composition and Crack Susceptibility Indices
The first thing any experienced welder does when handed a new steel grade is to pull the mill certificate and calculate the carbon equivalent and the cold crack susceptibility index. The paper follows this discipline. For NK-HITEN610U2, the key indices are as follows.
| Parameter | Value | Acceptance Criterion | Practical Significance |
|---|---|---|---|
| Carbon equivalent (CE, IIW) | Approx. 0.42–0.45% | ≤0.45% for penstock steel | Indicates weldability is marginal; preheat mandatory |
| Cold crack susceptibility index (Pcm) | Approx. 0.22–0.26% | ≤0.25% for high-strength steel | Pcm above 0.25 demands strict hydrogen control |
| Carbon content | Approx. 0.10–0.14% | Low carbon improves toughness | Quenched-tempered microstructure gives strength |
| Niobium + Vanadium | Microalloying elements | Controlled addition | Grain refinement in HAZ, but increases hardenability |
The paper correctly notes that although the carbon equivalent is within the generally accepted range for penstock steel, the Pcm value sits close to the upper limit, meaning the steel is sensitive to hydrogen-induced cold cracking if the welding consumable and process are not carefully controlled. In my experience, this is the classic trap: the steel meets the specification, but the margin is thin, and a damp electrode or a cold day on site can push the joint over the edge.
Diffusible Hydrogen and Its Role in Cold Cracking
The second factor the authors analyse is the diffusible hydrogen content of the weld metal. This is where many fabricators go wrong. For a 610 MPa class steel, the diffusible hydrogen limit is typically 5 mL/100 g for critical applications, and the paper confirms that this level can only be achieved with low-hydrogen electrodes (E7018 or equivalent) that have been properly baked and stored. The authors point out that even a small increase in diffusible hydrogen from 3 to 6 mL/100 g can dramatically raise the cold cracking risk at a given restraint level. The table below summarises the practical hydrogen control measures.
| Hydrogen Level (mL/100 g) | Risk Assessment | Required Control Measures |
|---|---|---|
| ≤3 | Low risk | Standard low-hydrogen electrodes, proper baking at 350–400°C for 1–2 h |
| 3–5 | Moderate risk | Strict electrode handling, preheat at 100–150°C, interpass control |
| 5–8 | High risk | Immediate danger; requires special low-hydrogen consumables, preheat above 150°C, post-weld hydrogen release treatment |
| >8 | Unacceptable | Do not proceed; re-evaluate consumable and storage practice |
The paper's contribution here is to link the hydrogen content directly to the structural restraint, showing that the two must be considered together. A low-restraint joint can tolerate a bit more hydrogen; a high-restraint joint cannot.
Structural Restraint and Its Interaction with Hydrogen
The third factor is structural restraint, which the authors quantify using the restraint intensity factor. For a thick-walled penstock, the restraint is inherently high because the pipe wall is rigid and the joint geometry does not allow much movement. The paper demonstrates that as restraint increases, the critical diffusible hydrogen content for cracking decreases sharply. This is the classic CCT (continuous cooling transformation) diagram logic: higher restraint means higher residual stress, which means less tolerance for hydrogen and a greater need for preheat.
In practical terms, the authors recommend a preheat temperature of 120–150°C for NK-HITEN610U2 penstock joints, with an interpass temperature not exceeding 200°C to avoid over-tempering the HAZ. They also stress the importance of post-weld heat treatment (PWHT) or at least a post-weld hydrogen release treatment at 200–250°C for 2 hours, particularly for joints with restraint intensity above a certain threshold.
Integration with Engineering Practice
Case Study: A Penstock Fabrication Incident
I recall a project in Southwest China where a 10 mm thick NK-HITEN610U2 penstock section developed transverse cracks in the HAZ after welding. The root cause was a combination of three factors that the paper would have predicted: the electrodes had been left open on the site floor overnight and absorbed moisture, raising the diffusible hydrogen to an estimated 7–8 mL/100 g; the ambient temperature was below 5°C, so the preheat was ineffective; and the joint was a high-restraint closure weld between two already-fixed pipe sections. The cracks were found by UT after 48 hours, confirming the delayed nature of hydrogen-induced cold cracking. The fix was straightforward but expensive: grind out the cracks, re-weld with freshly baked electrodes, maintain a preheat of 150°C with a temperature-indicating crayon, and apply a 250°C post-weld hydrogen release treatment for 2 hours. No further cracks appeared.
Practical Lessons for the Shop Floor and Site
- Never trust the mill certificate alone. Always verify the actual carbon equivalent and Pcm from the delivered heat, because within-lot variation can be significant.
- Electrode storage and handling is not a secondary concern. It is the primary control for cold cracking. Use portable electrode ovens on site, and log the baking and holding times.
- Preheat is not a suggestion. For high-strength penstock steel, measure the preheat at the joint, not at the pipe surface 500 mm away, and verify it with a contact pyrometer.
- The interpass temperature limit is as important as the preheat. Overheating the HAZ above 200°C will cause grain growth and toughness degradation, even if it does not crack.
- Post-weld hydrogen release treatment should be considered mandatory for high-restraint joints, even when PWHT is not specified.
Standards and Code Requirements
The paper's findings align with the requirements of API 5L for line pipe and with the Chinese standard GB 50766 for hydraulic steel structures. For NK-HITEN610U2 penstocks, the relevant standard is typically GB/T 2975 or the Japanese JIS G 3129, but the welding procedure qualification should be performed to ASME Section IX or ISO 15614-1, with the additional requirement for hardness testing of the HAZ. The table below summarises the typical acceptance criteria for this steel grade.
| Test Item | Acceptance Criterion | Standard Reference |
|---|---|---|
| HAZ hardness (HV10) | ≤350 HV for penstock steel | ASME B31.3 / GB 50766 |
| Charpy impact energy at -20°C | ≥47 J average, ≥31 J single | ISO 148 / GB/T 229 |
| Diffusible hydrogen | ≤5 mL/100 g | ISO 3690 |
| NDT (RT/UT) | No cracks, no unacceptable indications | ASME B31.3 / API 5L |
Key Questions and Reflections
The paper raises a question that I have often asked myself: why do we still see cold cracking in high-strength steel welds when the technology to prevent it has been known for decades? The answer, in my experience, is not technical ignorance but process discipline. The paper's analytical framework is sound, but the real challenge is ensuring that every welder on site understands the consequences of leaving an electrode can open for one night. I have seen projects where the welding procedure specification was impeccable, but the execution was sloppy, and the result was a cracked joint that cost more in rework than the entire welding consumable budget.
Another reflection concerns the hot cracking aspect. The paper mentions hot cracking but does not dwell on it, which is appropriate because NK-HITEN610U2 is not particularly susceptible to hot cracking due to its low sulphur and phosphorus content. However, I would caution that hot cracking can still occur if the weld metal composition is not controlled, particularly if the filler wire has high residual elements. The welding engineer should always review the consumable certificate for sulphur and phosphorus limits.
Study Insights and Implications
This paper is a reminder that welding high-strength steel is a system problem, not a single-variable problem. The chemical composition, the hydrogen content, and the restraint are not independent; they interact in a way that can turn a seemingly acceptable joint into a failure. The authors have done a service by quantifying these interactions for NK-HITEN610U2, but the real value lies in translating those numbers into a disciplined process control plan.
For the fabrication shop, the implications are clear: invest in proper electrode storage, enforce preheat and interpass controls, and do not compromise on post-weld heat treatment. For the site engineer, the message is equally clear: treat every high-strength penstock weld as a critical weld, even if the code does not classify it as such. The cost of prevention is a fraction of the cost of repair, and the cost of repair is a fraction of the cost of a failure in service.
Reference Value and Outlook
The paper is a solid reference for anyone working with NK-HITEN610U2 or similar quenched-and-tempered high-strength steels in penstock or pressure vessel applications. Its analytical approach can be extended to other grades, and its emphasis on the interaction between hydrogen and restraint is particularly valuable. Looking forward, I would like to see more research on the effect of modern low-hydrogen consumables and on the use of automated welding processes to reduce the human variability that is often the root cause of cracking. The industry is moving towards higher strength steels for penstocks, and the lessons from this paper will become even more relevant as we push beyond 700 MPa yield strength. In the meantime, the practical guidance remains: control the hydrogen, control the preheat, and respect the restraint. That is the recipe for crack-free penstock welding, and it has not changed in fifty years.
Zhuojin Pipe Fitting Co., Ltd