ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Lessons from 4130X Continuous Casting Start-Up Heat: Ultrasonic Inspection Failures and Secondary Oxidation

Literature Overview and Why This Paper Matters

This paper from Jiangsu Yonggang Group addresses a problem every seamless pipe producer has faced at some point: the first heat of a continuous casting sequence — the so-called "open-up" or "start-up" heat — produces billets that fail ultrasonic inspection downstream. The authors took 4130X gas cylinder steel, cast as 500 mm round billets, and systematically sampled from the hook head (the first solidified portion) at increasing distances to track oxygen, nitrogen, aluminium loss, and non-metallic inclusion behaviour. The findings are not surprising to anyone who has run a caster, but the quantification is valuable: the closer to the hook head, the higher the oxygen and nitrogen, the greater the aluminium loss, and the more severe the B, D, and DS inclusions. The paper also shows that secondary oxidation during open-up disproportionately affects inclusions of 5 μm and larger — precisely the size range that triggers ultrasonic rejection.

For a veteran, this paper is a reminder of a fundamental truth: the first heat of a sequence is a different animal. The tundish is cold, the shroud is not yet submerged, the mould level is unstable, and the steel is exposed to air at multiple points. If you do not control that window, you will pay for it downstream — in rejected pipe, in delayed deliveries, and in customer claims.

Technical Points and Their Practical Implications

The Mechanism of Secondary Oxidation

Secondary oxidation occurs when molten steel contacts air or oxidising slag. During open-up, the ladle stream is exposed to atmosphere until the shroud is submerged, the tundish fills with exposed steel, and the tundish-to-mould stream is similarly exposed until the mould level stabilises. Each contact point introduces oxygen, which reacts with dissolved aluminium to form alumina inclusions. The paper's data confirms this: aluminium loss increases closer to the hook head, and oxygen content rises correspondingly.

The practical takeaway is that the open-up heat should be treated as a "sacrificial" heat from a quality standpoint. You cannot fully eliminate secondary oxidation during open-up; you can only manage it. That means either diverting the open-up heat to less demanding applications or implementing aggressive measures to minimise exposure — argon shrouding, rapid tundish filling, early submergence, and careful mould level control.

Inclusion Types and Sizes

The paper identifies B-type (alumina), D-type (globular oxides), and DS-type (large single oxides) inclusions as the culprits. B-type inclusions are the classic product of aluminium deoxidation — hard, angular alumina particles that are excellent reflectors for ultrasonic waves. DS inclusions are particularly dangerous because they are large and singular, creating discrete reflectors that can be mistaken for laminations or cracks.

The size distribution finding is critical: secondary oxidation during open-up preferentially generates inclusions of 5 μm and larger. Smaller inclusions (below 5 μm) are less affected. This makes sense from a nucleation and growth standpoint — the longer the exposure time and the higher the local oxygen concentration, the more opportunity for inclusions to grow and agglomerate. For ultrasonic inspection, the relevant threshold is typically 1-2 mm equivalent reflector size, but clusters of 5 μm+ inclusions can form larger reflectors when they agglomerate.

The Hook Head Effect

The hook head — the first solidified portion of the billet — is the most contaminated region. The paper shows a clear gradient: the closer to the hook head, the worse the quality. This is because the first steel to enter the mould is the first to be exposed to secondary oxidation, and it solidifies before the casting process stabilises. The hook head also tends to have poor surface quality and may contain entrained slag or mould powder.

For practical purposes, the hook head should be cropped generously. Many plants crop 1-2 metres from the start of each heat, but for open-up heats, a longer crop — 3 metres or more — may be justified. The paper's data supports this: the worst contamination is within the first metre, but significant improvement may not occur until 2-3 metres.

Process Window and Countermeasures

Parameter Normal Heat Open-Up Heat Recommended Practice
Tundish filling time 3-5 min 5-10 min Minimise via rapid filling, argon shrouding
Shroud submergence Before filling After filling Submerge as early as possible
Mould level control ±5 mm ±10-15 mm Tighten control, use auto-level early
Al loss (ppm) <50 100-300+ Monitor, divert heat if excessive
O content (ppm) <20 30-80+ Sample at hook head, verify
B-type inclusion rating ≤1.0 2.0-3.0+ Crop longer, divert to lower-grade application
Cropping length 1-2 m 3-5 m Extend crop for open-up heats

The countermeasures fall into three categories:

  1. Prevention: Use argon shrouding at all exposed streams, pre-heat the tundish to reduce initial cooling, and fill the tundish rapidly to minimise exposure time. Some plants use a "dummy" tundish for the first heat to stabilise the casting process before switching to production tundishes.
  2. Detection: Sample the hook head for oxygen, nitrogen, and aluminium loss. If the loss exceeds a threshold, either crop more aggressively or divert the heat to a less demanding application. Ultrasonic inspection of the billet itself is the final gate.
  3. Mitigation: If the heat must be used for gas cylinder pipe, consider increasing the ultrasonic inspection sensitivity and cropping the affected length. Alternatively, use the heat for non-critical applications where surface quality and inclusion content are less demanding.

Engineering Practice and Real-World Lessons

I have seen this problem play out in multiple plants. In one case, a 4130X heat failed ultrasonic inspection at the pipe stage, and the entire heat was scrapped. The root cause was traced back to a tundish that was not properly pre-heated, causing the first steel to freeze and then remelt, creating a double-oxidation event. The cost was significant — not just the steel, but the lost production time and the delivery delay.

In another case, the plant had a standing rule to crop 2 metres from every open-up heat, but the rule was relaxed during a production push. The result was a batch of pipe that failed inspection at the customer's site, leading to a claim and a long negotiation. The lesson: quality rules exist for a reason, and they should not be relaxed under schedule pressure.

The paper's recommendation to treat the open-up heat as a distinct quality event is sound. In practice, I would add two more measures:

  1. Use a sacrificial tundish: If the casting sequence is long enough, use a separate tundish for the open-up heat and discard it after the first heat. This prevents contamination of the production tundish.
  2. Increase ultrasonic sensitivity for open-up heats: If the heat must be used, inspect at a higher sensitivity level and mark the affected length for cropping at the pipe stage.

Key Questions and Reflections

The paper raises a question that every quality manager should ask: what is the economic trade-off between cropping more aggressively and accepting a higher rejection rate downstream? The answer depends on the value of the product. For gas cylinder pipe, where ultrasonic inspection is mandatory and the consequences of failure are severe, aggressive cropping is justified. For less critical applications, a more relaxed approach may be acceptable.

Another question is whether the 5 μm threshold is the right one. The paper shows that secondary oxidation affects inclusions of 5 μm and larger, but the ultrasonic inspection threshold is typically much larger. The relationship between inclusion size distribution and ultrasonic detectability is not linear — clusters of small inclusions can form larger reflectors, and the paper's finding that secondary oxidation increases the density of 5 μm+ inclusions is the key link.

Study Insights and Implications

This paper is a valuable reference for any plant that casts aluminium-killed steels for critical applications. The methodology — sampling from the hook head at increasing distances and tracking oxygen, nitrogen, aluminium loss, and inclusion ratings — is a practical quality control tool that can be implemented without sophisticated equipment. The findings confirm what many of us have suspected but never quantified: the open-up heat is a distinct quality event that requires special handling.

For the industry, the implication is clear: if you are casting 4130X or similar grades for gas cylinder pipe, you need a written procedure for open-up heats that specifies cropping length, sampling frequency, and acceptance criteria. The procedure should be based on data, not intuition, and it should be reviewed periodically as casting conditions change.

Reference Value and Outlook

The paper's value lies in its practical approach. It does not propose a new theory or a complex model; it simply documents what happens in a real plant and provides a basis for informed decision-making. The data on oxygen, nitrogen, aluminium loss, and inclusion ratings as functions of distance from the hook head is directly usable for setting cropping lengths and acceptance criteria.

Looking forward, the industry should consider whether the open-up heat should be treated as a separate product category, with its own specifications and acceptance criteria. This would allow plants to use the heat for less demanding applications without the risk of downstream failures. It would also make the quality control process more transparent, as customers would know exactly what they are getting.

In the end, the paper is a reminder that quality is not a laboratory exercise — it is a production discipline. The open-up heat is a moment when the discipline is most tested, and the plant that manages it well will have fewer rejects, fewer claims, and happier customers. That is the real lesson.