ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Numerical Simulation and Experimental Study of Multi-Pass Rotary Swaging of Inclined Pipe Fittings

Overview of the Study

This paper from South China University of Technology addresses a manufacturing process that is often overlooked in favor of more conventional forming methods: multi-pass rotary swaging for inclined pipe fittings. The authors chose 6061 aluminum alloy in the annealed condition, which is a common material for automotive exhaust system components. The work combines finite element analysis using MSC.MARC with experimental validation using grid circles and microstructural observation.

The significance of this work lies in its focus on non-axisymmetric, inclined parts. Most rotary swaging research deals with axisymmetric parts, where the process is relatively straightforward. Inclined parts introduce a three-dimensional stress state that is much more complex, and the strain distribution becomes highly non-uniform. The authors have done a thorough job of characterizing this non-uniformity and validating their simulation results against experimental measurements.

Key Technical Points and Process Interpretation

Strain Distribution Characteristics

The simulation results reveal a clear pattern of strain distribution. The equivalent stress shows a layered distribution along the axial direction, with the maximum value at the mouth of the part. The equivalent strain decreases from 0° to 180° in the circumferential direction, with the maximum at 0° and the minimum at 180°. Along the axial direction, the equivalent strain increases at 0° and decreases at 180° as you move from the start of the swaging to the mouth.

This non-uniform distribution is a direct consequence of the inclination. The part is not symmetric about the axis of rotation, so the material flow is different at different circumferential positions. The 0° region experiences more deformation because it is closer to the swaging dies, while the 180° region experiences less. This has important implications for the final part geometry and mechanical properties.

Wall Thickness Changes During Multi-Pass Swaging

The authors found that the wall thickness in the middle of the deformation zone increases during multi-pass swaging. This is due to the return pass of the swaging operation, which has a thickening effect. The return pass compresses the material in the radial direction, causing it to flow in the axial direction and increase the wall thickness. This is a useful finding because it means that multi-pass swaging can be used to control wall thickness to some extent.

The experimental results for wall thickness changes show a relative error of no more than 10% compared to the simulation. This is a good agreement and validates the finite element model. The 10% error is acceptable for this type of process, where the material behavior is complex and the boundary conditions are difficult to model precisely.

Development of an Exhaust Manifold Prototype

The ultimate goal of the research was to develop a prototype inclined exhaust manifold for automotive application. The authors successfully produced a prototype based on their theoretical analysis and experimental studies. This is a significant achievement because exhaust manifolds are complex parts with multiple branches and varying cross-sections. The success of the prototype demonstrates that the process is viable for production applications.

Engineering Practice Insights and Reflections

Rotary Swaging vs. Other Forming Processes

Rotary swaging is often chosen over other forming processes for specific reasons. It can produce parts with high dimensional accuracy and good surface finish, and it can be used to form parts that are difficult to produce by other methods. For inclined parts, rotary swaging offers advantages over hydroforming or stamping because it can produce the required geometry without the need for complex tooling.

However, rotary swaging is not a high-volume process. The cycle time is longer than stamping or hydroforming, and the tooling is more expensive. The process is best suited for low to medium volume production, or for parts that cannot be produced by other methods. The authors' success with the exhaust manifold prototype suggests that the process has potential for automotive applications, but the production volume must be carefully considered.

The Importance of Simulation in Process Development

The authors' use of finite element simulation is a good example of how simulation can be used to develop a process without extensive trial and error. The simulation allowed them to understand the strain distribution and wall thickness changes before building any tooling. This saved time and money, and it allowed them to optimize the process parameters before committing to production.

In my experience, simulation is often underused in pipe and fitting manufacturing. Many companies still rely on trial and error, which is expensive and time-consuming. The authors' approach is a good model for how simulation should be integrated into process development.

Material Considerations for Exhaust Systems

6061 aluminum alloy is a common material for automotive exhaust systems, but it is not the only option. The material must be able to withstand the high temperatures and corrosive environment of the exhaust system. 6061 has good formability and corrosion resistance, but it may not have the high-temperature strength required for some applications. The authors used the annealed condition, which is suitable for forming, but the final part may need to be heat treated to achieve the required strength.

Validation is Essential

The authors validated their simulation results with experimental measurements, which is essential for building confidence in the model. The 10% relative error is acceptable, but it should be noted that the error could be larger in other regions of the part. The validation should be extended to cover the full range of process parameters before the model is used for production.

Conclusions and Study Insights

This paper is a well-executed study of a complex forming process. The authors have combined simulation and experiment to characterize the strain distribution and wall thickness changes during multi-pass rotary swaging of inclined parts. The results provide valuable insight into the process, and the successful prototype demonstrates the viability of the approach.

For a practicing engineer, the most valuable takeaway is the methodology. The authors have shown how simulation can be used to understand a complex process and guide the development of a production-ready part. The validation of the simulation results against experimental measurements is a critical step that is often skipped in industrial practice.

The paper also highlights the importance of understanding the non-uniform strain distribution in inclined parts. This non-uniformity affects the final geometry and mechanical properties of the part, and it must be accounted for in the die design and process parameter selection. The authors' finding that the return pass of the swaging operation causes wall thickening is particularly useful, as it provides a means of controlling wall thickness.