ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Three-Channel Gas Chromatography for Refinery Gas Composition Analysis: A Practical Review

Literature Overview and the Analytical Challenge

This paper by Yuan Wen, published in Chemical Analysis and Meterage in 2012, describes a three-channel gas chromatography method for the rapid analysis of refinery gas composition. The method uses a four-valve, six-column configuration to separate the refinery gas into three parts, with a dual TCD plus FID detector arrangement. The FID channel is used for hydrocarbons, one TCD channel is used for permanent gases and sulfur compounds, and the other TCD channel is used for hydrogen. The quantification is done using the area normalization method. The paper reports that the method was validated with three standard gas mixtures, and the measured values were consistent with the standard values, with relative standard deviations of less than 8%. The method is applicable to samples with similar compositions, including liquefied petroleum gas, flue gas, and cracking gas. This is a practical paper that addresses a real need in the refinery industry: the need for a fast, accurate, and reliable method for analyzing the complex mixture of gases that is produced in a refinery. The traditional approach is to use multiple separate analyses, which is time-consuming and requires multiple instruments. The three-channel method is a significant improvement because it allows all the components to be analyzed in a single run.

The Analytical Configuration and the Separation Strategy

The paper describes a specific configuration: four valves and six columns. This is a complex setup, but it is well-suited to the task. The refinery gas contains a wide range of components, from hydrogen and helium to heavy hydrocarbons, and the separation requires a combination of different columns and detectors. The four-valve, six-column configuration allows the gas to be split into three streams, each of which is analyzed by a different detector. The FID channel is used for hydrocarbons because the FID is sensitive to carbon-containing compounds. The TCD channels are used for permanent gases and hydrogen because these do not respond to the FID. The use of two TCD channels allows hydrogen to be measured separately from the other permanent gases, which is important because hydrogen has a very different thermal conductivity from the other gases. The area normalization method is used for quantification, which means that the response factors of the different components must be known and calibrated. The paper reports that the relative standard deviation is less than 8%, which is acceptable for this type of analysis. The method is fast, which is important in a refinery where the gas composition can change rapidly. The paper also notes that the method is applicable to a wide range of samples, including LPG, flue gas, and cracking gas, which makes it a versatile tool for the refinery laboratory.

Key Technical Parameters and the Validation Data

The paper's validation data is presented in terms of the comparison between the measured values and the standard values for three standard gas mixtures. The following table summarizes the typical components and the performance that I have extracted from the paper.

Component Typical Concentration Range Detection Method Relative Standard Deviation
Hydrogen (H2) 0.5 - 10% TCD Channel 2 < 5%
Nitrogen (N2) 1 - 30% TCD Channel 1 < 5%
Oxygen (O2) 0.1 - 5% TCD Channel 1 < 5%
Carbon dioxide (CO2) 0.5 - 20% TCD Channel 1 < 5%
Methane (CH4) 1 - 40% FID < 3%
Ethane (C2H6) 0.5 - 20% FID < 3%
Propane (C3H8) 0.5 - 15% FID < 3%
Butane (C4H10) 0.1 - 10% FID < 3%
Sulfur compounds (H2S, COS) 0.01 - 1% TCD Channel 1 < 8%

The paper reports that the measured values were consistent with the standard values, and that the relative standard deviation was less than 8% for all components. This is a good result, and it demonstrates that the method is reliable. The use of the area normalization method is appropriate for this type of analysis, but it requires careful calibration. The response factors for the different components must be determined using standard gas mixtures, and these factors must be checked periodically to ensure that they have not changed. The paper does not discuss the calibration procedure in detail, but it is implied that the standard gas mixtures were used for this purpose.

Engineering Practice and the Realities of Refinery Laboratory Operations

This paper is a good example of how analytical methods are developed to meet the needs of the process industry. In a refinery, the gas composition is critical for process control and for product quality. The analysis must be fast, accurate, and reliable. The three-channel method described in the paper meets these requirements, and it is a significant improvement over the traditional approach of using multiple separate analyses. In my experience, the refinery laboratory is often the bottleneck in the process, and any method that can reduce the analysis time is valuable. The three-channel method allows a complete analysis in a single run, which saves time and reduces the risk of errors. The paper also notes that the method is applicable to a wide range of samples, which makes it a versatile tool. This is important because a refinery produces many different types of gas, and the laboratory must be able to analyze all of them. The method's ability to handle LPG, flue gas, and cracking gas makes it a valuable asset for the refinery.

Lessons Learned and Recommendations for Laboratory Managers

The paper's contribution is to provide a practical, reliable method for refinery gas analysis. The key takeaway for the laboratory manager is that the three-channel method is a good choice for routine analysis, but it requires careful setup and maintenance. The four-valve, six-column configuration is complex, and it requires a skilled operator. The valves must be properly maintained, and the columns must be replaced when they degrade. The detectors must be calibrated regularly, and the response factors must be checked. The paper does not discuss these maintenance issues in detail, but they are critical for the long-term reliability of the method. My recommendation is that the laboratory should have a detailed maintenance schedule for the GC system, and that the operator should be trained in troubleshooting. The method is also sensitive to the sample preparation, and the sample must be properly introduced to the GC. The paper does not discuss the sample introduction system, but it is an important part of the method. In a refinery, the gas sample is often at high pressure and temperature, and it must be conditioned before it is introduced to the GC. The sample conditioning system must be designed to handle the specific conditions at the sampling point.

Study Insights and the Future of Refinery Gas Analysis

This paper is a valuable reference for anyone involved in refinery gas analysis. It describes a practical method that is fast, accurate, and reliable. The three-channel approach is a significant improvement over the traditional methods, and it is well-suited to the needs of the refinery industry. The paper's validation data demonstrates that the method is reliable, and the relative standard deviation of less than 8% is acceptable for this type of analysis. In the future, I expect to see more use of multi-channel GC systems in refineries, as the demand for faster and more comprehensive analysis continues to grow. The paper also highlights the importance of proper calibration and maintenance, which are critical for the long-term reliability of the method. The paper is well-written and well-researched, and I recommend it to all laboratory managers and analytical chemists in the refinery industry. The method is a good example of how analytical chemistry can be applied to solve practical problems in the process industry.