Application of Layout and Cutting Technology for Eccentric Concentric Oblique Tees: A Shop Floor Perspective
Literature Overview and Practical Relevance
This paper by Chen Feng, from the International Division of Daqing Oilfield Engineering Construction Co., Ltd., published in Petroleum and Chemical Equipment (2019, Vol. 22, No. 7), presents a computer-aided layout and cutting method for eccentric concentric oblique tees. The author uses SolidWorks software to generate the intersection curve and the development pattern, which is then used for cutting the plate or pipe. The paper compares this method with the traditional manual calculation and layout method, highlighting the improvements in efficiency and accuracy.
This is a practical, shop-floor-oriented paper that addresses a real problem in the fabrication of pipe fittings. In the oil and gas industry, we often need to fabricate custom tees, especially for large-diameter pipes where standard fittings are not available or are too expensive. The traditional method of laying out an oblique tee is time-consuming and error-prone. The use of 3D CAD software, such as SolidWorks, can significantly improve the accuracy and speed of the layout.
Core Findings and Technical Interpretation
The Challenge of Oblique Tee Layout
An eccentric concentric oblique tee is a fitting where the branch is not perpendicular to the main pipe, and the branch centerline is offset from the main pipe centerline. This geometry is common in piping systems where the branch needs to connect to a main pipe at an angle, and the flow path needs to be smooth to minimize pressure drop. The layout of such a tee is complex because the intersection curve is not a simple ellipse; it is a three-dimensional curve that must be accurately calculated and transferred to the plate or pipe.
| Geometry Parameter | Traditional Method | SolidWorks Method |
|---|---|---|
| Intersection curve | Calculated manually, point by point | Generated automatically, exact |
| Development pattern | Drawn manually, prone to error | Generated automatically, precise |
| Cutting accuracy | ±2-3 mm | ±0.5 mm or better |
| Layout time | 4-8 hours per tee | 30-60 minutes per tee |
The SolidWorks Approach
The paper describes the use of SolidWorks to create a 3D model of the tee, then use the "sheet metal" or "unfold" function to generate the development pattern. The steps are:
- Create the 3D model of the main pipe and the branch pipe, with the correct angle and offset.
- Use the "intersection" feature to create the intersection curve.
- Use the "sheet metal" or "lofted bend" feature to create the branch as a sheet metal part.
- Use the "flatten" function to generate the development pattern.
- Export the pattern as a DXF file for CNC cutting.
This approach is not only faster but also more accurate. The intersection curve is mathematically exact, and the development pattern is generated by the software, eliminating the errors associated with manual layout.
Practical Benefits on the Shop Floor
The paper highlights several practical benefits:
- Reduced layout time: The time to lay out a tee is reduced from hours to minutes.
- Improved accuracy: The cutting accuracy is significantly improved, reducing the need for grinding and fitting during assembly.
- Reduced material waste: The accurate development pattern minimizes the amount of material that is cut off and discarded.
- Better fit-up: The precise cutting ensures that the branch fits the main pipe with minimal gap, which is critical for welding.
Integration with Manufacturing and Delivery Practice
Fabrication Process for Custom Tees
In our industry, we often need to fabricate custom tees for large-diameter pipes. The process is:
- Design: Determine the pipe sizes, the branch angle, and the offset.
- Layout: Generate the development pattern using CAD software.
- Cutting: Cut the branch pipe and the main pipe opening using CNC cutting or plasma cutting.
- Fit-up: Align the branch and the main pipe, and tack weld.
- Welding: Weld the joint using a qualified welding procedure.
- Inspection: Inspect the weld with NDT methods.
The use of SolidWorks for the layout step is a significant improvement over the traditional method. It reduces the time and cost of fabrication, and it improves the quality of the final product.
Quality Control and Dimensional Accuracy
The dimensional accuracy of the tee is critical for the fit-up and the weld quality. If the branch is not cut accurately, the gap between the branch and the main pipe will be too large or too small, leading to weld defects. The use of CAD software ensures that the cutting is accurate, but we still need to verify the dimensions after cutting. The inspection should include:
| Inspection Item | Method | Acceptance Criteria |
|---|---|---|
| Branch angle | Protractor or template | ±1 degree |
| Branch offset | Tape measure | ±2 mm |
| Intersection curve | Template or CMM | ±1 mm |
| Wall thickness | Ultrasonic gauge | Per specification |
Cost and Schedule Impact
The use of CAD software for layout has a direct impact on the cost and schedule of the fabrication. The reduced layout time and the improved accuracy result in:
- Lower labor cost: Less time spent on layout and fitting.
- Lower material cost: Less waste from inaccurate cutting.
- Faster delivery: The fabrication time is reduced, allowing us to meet the project schedule.
Key Questions and Reflections
- What is the limitation of this method? The SolidWorks method is limited by the complexity of the geometry. For a simple oblique tee, it works well. For a tee with multiple branches or a complex intersection, the software may struggle to generate the development pattern. In such cases, a more advanced method, such as finite element analysis, may be required.
- Can this method be used for all pipe sizes? Yes, the method is scalable. It works for small pipes and large pipes. The key is to have a CNC cutting machine that can handle the pipe size and the plate thickness.
- What are the potential errors? The main potential errors are in the 3D model, not in the development pattern. If the pipe sizes, the angle, or the offset are entered incorrectly, the development pattern will be wrong. Therefore, it is essential to verify the input parameters before generating the pattern.
Study Insights and Implications for Our Work
This paper is a practical guide for the fabrication of custom tees. It highlights the benefits of using CAD software for layout and cutting, and it provides a clear step-by-step process. For our industry, the key insights are:
- CAD software is a powerful tool for fabrication. It can generate accurate development patterns for complex geometries, reducing the time and cost of fabrication.
- The accuracy of the layout is critical for the weld quality. A precise fit-up is essential for a sound weld.
- The use of CNC cutting is essential for large-diameter pipes. Manual cutting is not accurate enough for the large pipe sizes used in the oil and gas industry.
Reference Value and Outlook
For our industry, the direct application of this paper is in the fabrication of custom tees and other pipe fittings. The method can be extended to other complex geometries, such as wyes, crosses, and manifolds. The next step would be to develop a comprehensive library of development patterns for standard and non-standard fittings, which would further reduce the layout time and improve the accuracy.
In conclusion, this paper is a valuable contribution to the field of pipe fitting fabrication. It demonstrates the benefits of using CAD software for layout and cutting, and it provides a practical method that can be implemented on the shop floor. As a manufacturer and supplier of pipe and fittings, we should adopt this method to improve our efficiency and quality. The investment in CAD software and CNC cutting machines will pay for itself in reduced labor costs and improved product quality.
Zhuojin Pipe Fitting Co., Ltd