ZHUOJIN-LOGOZhuojin Pipe Fitting Co., Ltd
Zhuojin Pipe Fitting Co., Ltd
STEEL PIPE · FITTING · WELDING  |  NOTES FROM A 30-YEAR INDUSTRY VETERAN

Hot Extrusion Tee Forming and Its Innovative Manufacturing Process

Literature Overview and Core Concept

Zhang Shuangli's 2022 paper in Petrochemical Technology addresses a persistent headache in our industry: how to make a hot-extruded tee with less capital, less energy, and less scrap. The author, from Yingkou Liaohe Pipe Fittings Co., Ltd., describes a modified process sequence using a new type of hydraulic press that preserves the fundamental forming principle while reordering the steps. The stated goal is to save energy, reduce equipment cost, and ultimately lower production cost while improving enterprise competitiveness.

This is not a breakthrough in metallurgy or a new alloy. It is a process engineering paper, and that is exactly what the shop floor needs. In my thirty years in this business, I have seen more money lost to clumsy process sequencing than to any metallurgical mystery. The paper's value lies in its honesty about the traditional route's weaknesses and its demonstration that the same physical principle, executed in a better order, can change the economics of a fitting shop.

Traditional Process Analysis and Its Limitations

The conventional hot extrusion tee process follows a sequence that has been around since the mid-twentieth century. The billet is heated, placed in the die, and the main body is formed by axial compression while the branch is extruded through a side opening. The punch advances, material flows into the branch cavity, and the wall thickness distribution is controlled by the geometry of the die and the temperature profile.

The traditional sequence has several inherent problems that any plant manager will recognize immediately:

Traditional Step Practical Issue Consequence
Billet heating Large furnace footprint, high energy input High fixed cost per piece
Pre-forming operation Requires separate press or handling equipment Extra capital and labor
Main extrusion stroke High tonnage requirement, long stroke Large press, high energy per cycle
Branch extrusion Difficult to control wall thinning at branch root Scrap or rework on critical fittings
Subsequent trimming and sizing Additional operations, potential for distortion Longer cycle time, more handling

The paper identifies that by reordering the sequence—specifically, by performing certain forming steps in a different order or combining operations—the required press capacity can be reduced. This is not merely a theoretical observation. In practice, a reduction in required tonnage directly translates to a smaller, cheaper press, lower foundation cost, and lower energy consumption per cycle. For a fitting manufacturer competing on price, this is the difference between winning and losing a tender.

The Innovative Process Sequence and Its Technical Rationale

The author describes using a new hydraulic press that allows the process sequence to be reorganized. The key insight is that if the branch is extruded first, or if the pre-forming and final forming are combined into a single press stroke with controlled pressure profiles, the material flow path becomes shorter and the required force drops.

Let me explain the physics in practical terms. In a conventional tee extrusion, the punch must overcome the resistance of the entire billet cross-section plus the friction along the die walls. The branch extrusion requires additional force because the material must be forced to turn ninety degrees and flow through the branch opening. If you can pre-shape the billet to create a preferential flow path, or if you can apply the branch extrusion force while the main body is still being formed, the material does not have to overcome the full resistance of a solid billet.

The new process, as I understand it from the paper, achieves this by changing the sequence so that the branch is partially formed before the main body reaches its final dimensions. This reduces the peak force required and allows a smaller press to do the same job. The energy savings come from two sources: lower peak hydraulic pressure and fewer heating cycles if the process can be completed in a single heat.

Engineering Practice and Shop Floor Considerations

I have seen the traditional process run in plants across China and Southeast Asia, and I have watched operators struggle with the same problems the paper describes. The typical issues are wall thinning at the branch root, uneven wall thickness distribution around the branch opening, and excessive flash that requires grinding. The innovative sequence addresses these by improving material flow, but it also introduces new challenges.

One practical concern is temperature management. If the process is reordered, the time the billet spends in the die changes, and the temperature gradient across the billet may shift. The operator must be vigilant about the billet's temperature at the moment of branch extrusion. Too cold, and the material will not flow; too hot, and the branch will thin excessively or the grain growth will degrade mechanical properties.

Another concern is die design. The new sequence may require a modified die geometry to accommodate the reordered flow. This is not a trivial matter. I have seen shops attempt to modify a process sequence without redesigning the die, only to produce scrap for a week before admitting the die needed rework.

The paper's contribution is that it presents the reordering as a viable path without requiring a complete redesign of the press or the die. It is an optimization of the existing principle, not a revolution. This is the kind of incremental improvement that a practical shop can implement with modest investment.

Key Questions and Reflections

The paper raises a question that I have asked many times in my career: is the process innovation worth the risk? For a shop producing standard tees in high volume, the answer is clearly yes. The energy savings and reduced equipment cost compound over thousands of pieces. For a shop producing specialty tees in small batches, the answer is less clear, because the die modification and process qualification costs are amortized over fewer pieces.

There is also the question of qualification. Any change to a forming process that affects wall thickness distribution and mechanical properties must be re-qualified. This means new burst tests, new tensile tests, new hardness surveys, and potentially new ultrasonic or radiographic inspection requirements. The paper does not dwell on this, but the shop floor knows that process changes are not free.

The paper also implies that the new process can be implemented on a smaller press, which means lower foundation cost and lower energy consumption. But the press is not the only cost. The die, the heating system, the handling equipment, and the inspection regime all contribute to the total cost per piece. The paper's focus on press capacity is appropriate, but the veteran knows that the total system cost is what matters.

Study Insights and Implications for the Industry

This paper is a reminder that process optimization is not about exotic technology. It is about understanding the physics of material flow and applying that understanding to reduce waste. The traditional hot extrusion tee process has been refined over decades, but there is still room for improvement in how the steps are sequenced.

For the industry, the implication is that competitive advantage in pipe fittings often comes from process engineering rather than from material science. A shop that can produce a standard tee with 10 percent less energy and 5 percent less scrap will win the contract every time, regardless of the alloy or the standard being met.

The paper also highlights the importance of equipment selection. A new hydraulic press with precise pressure control and programmable stroke profiles enables process innovations that were not possible with older, simpler presses. This is a capital investment decision, but one that pays back through lower operating costs.

Conclusion

Zhang Shuangli's paper is a concise, practical contribution to the field of tee fitting manufacturing. It demonstrates that reordering the hot extrusion process sequence can reduce energy consumption and equipment cost without changing the fundamental forming principle. For the shop floor, this means a path to lower production cost and improved competitiveness. For the engineer, it is a reminder that process sequencing is a powerful lever for cost reduction. For the industry, it reinforces that innovation in pipe fittings is often incremental and process-focused rather than revolutionary and material-focused. The paper is worth reading for anyone involved in fitting manufacturing, and its principles are applicable beyond tees to other extruded fittings. The key is to understand the material flow, respect the temperature window, and be willing to re-qualify the process when changes are made. That is the veteran's advice, and it has served me well for three decades.