High-Frequency Proportional Pressure Reducing Valve Optimization and Its Application in Pipe Mill Hydraulics
Literature Overview and Core Content
The paper by Liu Jinrong, Zhang Yuxin, Liu Feng, and Liang Mingyuan, published in Ship Engineering (2025, Vol. 47, S1), presents an optimization study of a high-frequency three-way proportional pressure reducing valve for an electro-hydraulic variable valve system. The authors built a dynamic model of the valve, analyzed the effects of key structural parameters — coil turns, wire diameter, and negative overlap — on dynamic response, and performed multi-parameter co-optimization based on simulation results. The optimized valve achieved a rise time of 2.5 ms, a frequency response of 130 Hz, and significantly improved dynamic hysteresis.
For a steel pipe veteran, this paper is directly relevant to the hydraulic systems that run pipe mills. High-frequency proportional valves are used in many critical applications: the hydraulic gap control in a rolling mill, the tension control in a continuous pipe mill, the position control in a pipe handling system, and the pressure control in a hydrostatic testing unit. The performance of these valves directly affects the quality of the pipe and the efficiency of the mill.
Technical Points and Practical Interpretation
The Role of Structural Parameters in Dynamic Response
The paper identifies three key structural parameters: coil turns, wire diameter, and negative overlap. These parameters determine the electromagnetic force, the magnetic flux, and the flow characteristics of the valve. In a pipe mill, the equivalent parameters are the design of the hydraulic cylinder, the servo valve, and the control algorithm.
| Parameter | Effect on Dynamic Response | Practical Consideration in Pipe Mill |
|---|---|---|
| Coil Turns | Affects electromagnetic force and response time | Higher turns increase force but may increase inductance and slow response |
| Wire Diameter | Affects current capacity and heat generation | Larger diameter reduces resistance but may limit turns in a given space |
| Negative Overlap | Affects flow gain and stability | More overlap improves stability but reduces response and increases dead zone |
In a rolling mill, the hydraulic gap control system uses a servo valve to control the position of the rolls. The response time of the servo valve determines how quickly the mill can correct for variations in strip thickness. If the valve is too slow, the thickness control is poor, and the pipe wall thickness varies beyond tolerance.
Frequency Response and Stability
The paper emphasizes frequency response as a key performance metric. A frequency response of 130 Hz means the valve can track a command signal that changes at 130 cycles per second. In a pipe mill, this is important for high-speed applications. For example, in a continuous pipe mill, the welding speed can be several meters per minute, and the control system must respond to variations in strip width, thickness, and temperature.
The stability of the valve is also critical. If the valve is unstable, it will oscillate, causing pressure fluctuations that can damage the hydraulic system or produce poor quality pipe. The paper's optimization approach — using simulation to explore the parameter space and then validating with tests — is exactly the right methodology for valve development.
Engineering Practice Cases and Lessons
Case 1: Hydraulic Gap Control in a Pipe Mill
I once worked with a mill that was producing pipe with excessive wall thickness variation. The hydraulic gap control system was not responding fast enough to correct for variations in the incoming strip. The servo valve was an older model with a frequency response of only 50 Hz. The mill was running at a speed that required a frequency response of at least 80 Hz.
The solution was to replace the servo valve with a higher-performance model. The new valve had a frequency response of 120 Hz and a rise time of 3 ms. The wall thickness variation was reduced by 40%, and the mill could run at a higher speed without compromising quality.
Case 2: Hydrostatic Testing Pressure Control
In another project, we were hydrostatic testing large diameter pipe. The pressure control system used a proportional valve to ramp up the pressure and maintain it during the test. The valve had excessive hysteresis, causing the pressure to overshoot the test pressure by 5%. This was unacceptable because the test pressure was already at 90% of the yield strength of the pipe.
The corrective action was to optimize the valve's control algorithm and to reduce the hysteresis through mechanical adjustments. The paper's finding that structural parameters affect hysteresis is directly applicable. By adjusting the negative overlap and the coil design, we were able to reduce the hysteresis to less than 1%, ensuring that the test pressure was accurately controlled.
Key Questions and Reflections
- How can we optimize the dynamic response of hydraulic valves in pipe mills without sacrificing stability?.
- What is the cost-benefit of upgrading to high-frequency proportional valves?.
- How can we validate valve performance in a production environment?.
These are practical questions. A high-frequency valve costs more than a standard valve, but the improvement in pipe quality and mill efficiency can justify the cost. The key is to quantify the benefit in terms of reduced scrap, reduced rework, and increased throughput.
Study Insights and Implications
The paper demonstrates that structural parameter optimization can significantly improve valve performance. In pipe mills, this is a reminder that the design of hydraulic components matters. A valve that is not optimized for its application will limit the performance of the entire system.
For pipe engineers, the implication is to work closely with hydraulic system suppliers to ensure that the valves are properly selected and optimized for the specific application. The paper's methodology — simulation, optimization, and validation — is a good model for this process.
Reference Value and Outlook
The paper is in the field of ship engineering, but its findings are directly applicable to pipe mill hydraulics. The optimization of high-frequency proportional valves is relevant to any application that requires fast and precise control. The outlook is for even higher performance valves, with frequency responses approaching 200 Hz, enabled by advanced materials and control algorithms.
In conclusion, the valve optimization paper is a valuable reference for anyone involved in the design or maintenance of hydraulic systems in pipe mills. The lessons about structural parameters, frequency response, and stability are timeless and directly applicable.
Zhuojin Pipe Fitting Co., Ltd